Date: Sun, 29 Aug 2010 13:41:11 +0200 From: Hans Petter Selasky <hselasky@c2i.net> To: Matthew Luckie <mjl@luckie.org.nz> Cc: freebsd-usb@freebsd.org Subject: Re: ZTE USB 3g stick Message-ID: <201008291341.11379.hselasky@c2i.net> In-Reply-To: <4C78F7D7.7010507@luckie.org.nz> References: <4C789A4E.9030409@luckie.org.nz> <201008280950.35903.hselasky@c2i.net> <4C78F7D7.7010507@luckie.org.nz>
next in thread | previous in thread | raw e-mail | index | archive | help
On Saturday 28 August 2010 13:49:43 Matthew Luckie wrote: > On 08/28/10 19:50, Hans Petter Selasky wrote: > > On Saturday 28 August 2010 07:10:38 Matthew Luckie wrote: > >> Hi > >> > >> I've got a 3g usb stick that works fine with 8.0-STABLE from Jan 3rd > >> 2010, but does not with 8.1-RELEASE. Its a Vodafone branded stick > >> bought in New Zealand. > >> > >> With FreeBSD 8.0 it prints this when I insert the stick: > >> > >> usb_test_autoinstall: Eject CD command status: USB_ERR_PENDING_REQUESTS > >> ugen6.2:<ZTE,Incorporated> at usbus6 > >> ugen6.2:<ZTE,Incorporated> at usbus6 (disconnected) > >> ugen6.2:<ZTE,Incorporated> at usbus6 > >> u3g0:<ZTE,Incorporated ZTE CDMA Technologies MSM, class 0/0, rev > >> 2.00/0.00, addr 2> on usbus6 > >> u3g0: Found 5 ports. > >> umass0:<ZTE,Incorporated ZTE CDMA Technologies MSM, class 0/0, rev > >> 2.00/0.00, addr 2> on usbus6 > >> umass0: SCSI over Bulk-Only; quirks = 0x0000 > >> umass0:2:0:-1: Attached to scbus2 > >> (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > >> (probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error > >> (probe0:umass-sim0:0:0:0): SCSI Status: Check Condition > >> (probe0:umass-sim0:0:0:0): NOT READY asc:3a,0 > >> (probe0:umass-sim0:0:0:0): Medium not present > >> (probe0:umass-sim0:0:0:0): Unretryable error > >> da0 at umass-sim0 bus 0 scbus2 target 0 lun 0 > >> da0:<ZTE MMC Storage 2.31> Removable Direct Access SCSI-2 device > >> da0: 40.000MB/s transfers > >> da0: Attempt to query device size failed: NOT READY, Medium not present > >> > >> [mjl@mylar mjl]$ sudo usbconfig -u 6 dump_info > >> ugen6.1:<EHCI root HUB Intel> at usbus6, cfg=0 md=HOST spd=HIGH > >> (480Mbps) pwr=ON > >> > >> ugen6.2:<ZTE CDMA Technologies MSM ZTE,Incorporated> at usbus6, cfg=0 > >> md=HOST spd=HIGH (480Mbps) pwr=ON > >> > >> On FreeBSD 8.1 it prints this: > >> > >> ugen6.2:<ZTE,Incorporated> at usbus6 > >> > >> (and nothing else) > >> > >> [mjl@mylar mjl]$ sudo usbconfig -d 6.2 dump_device_desc > >> ugen6.2:<ZTE CDMA Technologies MSM ZTE,Incorporated> at usbus6, cfg=255 > >> md=HOST spd=HIGH (480Mbps) pwr=ON > >> > >> bLength = 0x0012 > >> bDescriptorType = 0x0001 > >> bcdUSB = 0x0200 > >> bDeviceClass = 0x0000 > >> bDeviceSubClass = 0x0000 > >> bDeviceProtocol = 0x0000 > >> bMaxPacketSize0 = 0x0040 > >> idVendor = 0x19d2 > >> idProduct = 0x2000 > >> bcdDevice = 0x0000 > >> iManufacturer = 0x0002<ZTE,Incorporated> > >> iProduct = 0x0001<ZTE CDMA Technologies MSM> > >> iSerialNumber = 0x0003<P673A2VDF_MS> > >> bNumConfigurations = 0x0001 > > > > Have you loaded the u3g driver before plugging the device. Also try: > Yes, I have. > > [mjl@mylar mjl]$ sudo kldload /boot/kernel/u3g.ko > kldload: can't load /boot/kernel/u3g.ko: File exists > > module_register: module uhub/u3g already exists! > Module uhub/u3g failed to register: 17 > > > usbconfig -d 6.2 set_config 0 > > ugen6.2: <ZTE,Incorporated> at usbus6 > umass0: <ZTE,Incorporated ZTE CDMA Technologies MSM, class 0/0, rev > 2.00/0.00, addr 2> on usbus6 > cd1 at umass-sim0 bus 0 scbus2 target 0 lun 0 > cd1: <ZTE USB SCSI CD-ROM 2.31> Removable CD-ROM SCSI-2 device > cd1: 40.000MB/s transfers > cd1: cd present [31484 x 2048 byte records] > > Sadly no /dev/cuaU* entries. After the set_config, I have new /dev > entries for cd1, iso9660, pass1, and of course ugen6.2. > > [mjl@mylar ~]$ sudo usbconfig -d 6.2 dump_device_desc > ugen6.2: <ZTE CDMA Technologies MSM ZTE,Incorporated> at usbus6, cfg=0 > md=HOST spd=HIGH (480Mbps) pwr=ON > > bLength = 0x0012 > bDescriptorType = 0x0001 > bcdUSB = 0x0200 > bDeviceClass = 0x0000 > bDeviceSubClass = 0x0000 > bDeviceProtocol = 0x0000 > bMaxPacketSize0 = 0x0040 > idVendor = 0x19d2 > idProduct = 0x2000 > bcdDevice = 0x0000 > iManufacturer = 0x0002 <ZTE,Incorporated> > iProduct = 0x0001 <ZTE CDMA Technologies MSM> > iSerialNumber = 0x0003 <P673A2VDF_MS> > bNumConfigurations = 0x0001 Hi, Possibly we need to add some code to check when the autoinstall system is ready for receiving the command. What happens if you try to add a delay before executing the eject command: --- src/sys/dev/usb/usb_msctest.c 2010-03-08 16:57:53.000000000 0000 +++ src/sys/dev/usb/usb_msctest.c 2010-03-08 16:57:53.000000000 0000 @@ -588,6 +588,8 @@ if (sc == NULL) return (USB_ERR_INVAL); + pause("WAIT", hz); + err = 0; switch (method) { case MSC_EJECT_STOPUNIT: --HPS
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201008291341.11379.hselasky>