Date: Mon, 31 Jan 2011 12:52:22 +0100 From: Damien Fleuriot <ml@my.gd> To: freebsd-stable@freebsd.org Subject: Re: KERN - mfi driver for Dell raid h200 on r210 servers Message-ID: <4D46A276.60304@my.gd> In-Reply-To: <20110130221826.GA41684@iqpano.freenix.org> References: <AANLkTikfZ_ba4w975Y9pB4inY2xWae2i0253SM=ie-G0@mail.gmail.com> <20110129222400.R39951@maildrop.int.zabbadoz.net> <AANLkTi=wbi3B%2BxSKBR-6TsFbBHWP26PE=HBUpKYBzG-1@mail.gmail.com> <20110130221826.GA41684@iqpano.freenix.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On 1/30/11 11:18 PM, Ollivier Robert wrote:
> According to Garrett Cooper:
>> +1. PERC7 should be supported by mfi(4) (required bits may need to
>> be added to mfi(4) though as you've pointed out, but additional
>> details may need to be obtained from Dell).
>
> I've seen mention of the mps driver (in head) and of the mfi one. Which one is the right one?
>
> For the OP: I may be gaining access to a test system (Dell R210 / as in new dedibox[1]) tomorrow on which I could test my mfsboot image...
>
As requested, find below the output of a verbose boot.
Notice how mps0 is rather unhappy here:
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
(probe1:mps0:0:1:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Down reving Protocol Version from 4 to 2?
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
(probe1:mps0:0:1:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Down reving Protocol Version from 4 to 2?
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Error 22, Unretryable error
Table 'FACP' at 0xbf6c3bb4
Table 'APIC' at 0xbf6c3478
APIC: Found table at 0xbf6c3478
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 2 ACPI ID 2: enabled
SMP: Added CPU 2 (AP)
MADT: Found CPU APIC ID 4 ACPI ID 3: enabled
SMP: Added CPU 4 (AP)
MADT: Found CPU APIC ID 6 ACPI ID 4: enabled
SMP: Added CPU 6 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 5: enabled
SMP: Added CPU 1 (AP)
MADT: Found CPU APIC ID 3 ACPI ID 6: enabled
SMP: Added CPU 3 (AP)
MADT: Found CPU APIC ID 5 ACPI ID 7: enabled
SMP: Added CPU 5 (AP)
MADT: Found CPU APIC ID 7 ACPI ID 8: enabled
SMP: Added CPU 7 (AP)
MADT: Found CPU APIC ID 40 ACPI ID 9: disabled
MADT: Found CPU APIC ID 41 ACPI ID 10: disabled
MADT: Found CPU APIC ID 42 ACPI ID 11: disabled
MADT: Found CPU APIC ID 43 ACPI ID 12: disabled
MADT: Found CPU APIC ID 44 ACPI ID 13: disabled
MADT: Found CPU APIC ID 45 ACPI ID 14: disabled
MADT: Found CPU APIC ID 46 ACPI ID 15: disabled
MADT: Found CPU APIC ID 47 ACPI ID 16: disabled
MADT: Found CPU APIC ID 48 ACPI ID 17: disabled
MADT: Found CPU APIC ID 49 ACPI ID 18: disabled
MADT: Found CPU APIC ID 50 ACPI ID 19: disabled
MADT: Found CPU APIC ID 51 ACPI ID 20: disabled
MADT: Found CPU APIC ID 52 ACPI ID 21: disabled
MADT: Found CPU APIC ID 53 ACPI ID 22: disabled
MADT: Found CPU APIC ID 54 ACPI ID 23: disabled
MADT: Found CPU APIC ID 55 ACPI ID 24: disabled
MADT: Found CPU APIC ID 56 ACPI ID 25: disabled
MADT: Found CPU APIC ID 57 ACPI ID 26: disabled
MADT: Found CPU APIC ID 58 ACPI ID 27: disabled
MADT: Found CPU APIC ID 59 ACPI ID 28: disabled
MADT: Found CPU APIC ID 60 ACPI ID 29: disabled
MADT: Found CPU APIC ID 61 ACPI ID 30: disabled
MADT: Found CPU APIC ID 62 ACPI ID 31: disabled
MADT: Found CPU APIC ID 63 ACPI ID 32: disabled
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.2-PRERELEASE #1 r218017M: Sat Jan 29 12:23:01 CET 2011
root@centre.keltia.net:/usr/obj/data/work/freebsd/8v28/sys/GENERIC amd64
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff83355000.
Preloaded elf obj module "/boot/kernel/zfs.ko" at 0xffffffff833551b8.
Preloaded elf obj module "/boot/kernel/opensolaris.ko" at
0xffffffff83355820.
Preloaded mfs_root "/mfsroot" at 0xffffffff83355e10.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1861998768 Hz
CPU: Intel(R) Xeon(R) CPU L3426 @ 1.87GHz (1862.00-MHz
K8-class CPU)
Origin = "GenuineIntel" Id = 0x106e5 Family = 6 Model = 1e
Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x98e3fd<SSE3,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 17179869184 (16384 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x0000000000097fff, 618496 bytes (151 pages)
0x0000000003390000 - 0x00000000bf698fff, 3157299200 bytes (770825 pages)
0x0000000100000000 - 0x00000004200affff, 13422493696 bytes (3276976 pages)
avail memory = 16476315648 (15713 MB)
ACPI APIC Table: <DELL PE_SC3 >
INTR: Adding local APIC 1 as a target
INTR: Adding local APIC 2 as a target
INTR: Adding local APIC 3 as a target
INTR: Adding local APIC 4 as a target
INTR: Adding local APIC 5 as a target
INTR: Adding local APIC 6 as a target
INTR: Adding local APIC 7 as a target
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s) x 2 SMT threads
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
x86bios: IVT 0x000000-0x0004ff at 0xffffff0000000000
x86bios: SSEG 0x010000-0x01ffff at 0xffffff8000063000
x86bios: EBDA 0x09c000-0x09ffff at 0xffffff000009c000
x86bios: ROM 0x0a0000-0x0effff at 0xffffff00000a0000
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 5
APIC: CPU 2 has ACPI ID 2
APIC: CPU 3 has ACPI ID 6
APIC: CPU 4 has ACPI ID 3
APIC: CPU 5 has ACPI ID 7
APIC: CPU 6 has ACPI ID 4
APIC: CPU 7 has ACPI ID 8
lapic0: CMCI unmasked
ULE: setup cpu 0
ULE: setup cpu 1
ULE: setup cpu 2
ULE: setup cpu 3
ULE: setup cpu 4
ULE: setup cpu 5
ULE: setup cpu 6
ULE: setup cpu 7
ACPI: RSDP 0xf0b40 00024 (v02 DELL )
ACPI: XSDT 0xf0c40 00094 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: FACP 0xbf6c3bb4 000F4 (v03 DELL PE_SC3 00000001 DELL 00000001)
ACPI: DSDT 0xbf6af000 0398C (v01 DELL PE_SC3 00000001 INTL 20050624)
ACPI: FACS 0xbf6c6000 00040
ACPI: APIC 0xbf6c3478 00152 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: SPCR 0xbf6c35cc 00050 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: HPET 0xbf6c3620 00038 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: DMAR 0xbf6c365c 000A8 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: MCFG 0xbf6c3850 0003C (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: WD__ 0xbf6c3890 00134 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI: SLIC 0xbf6c39c8 00024 (v01 DELL PE_SC3 00000001 DELL 00000001)
ACPI Error: Null physical address for ACPI table [(null)]
(20101013/tbutils-512)
ACPI Error: Null physical address for ACPI table [(null)]
(20101013/tbutils-512)
ACPI Error: Null physical address for ACPI table [(null)]
(20101013/tbutils-512)
ACPI Error: Null physical address for ACPI table [(null)]
(20101013/tbutils-512)
ACPI: TCPA 0xbf6c3b4c 00064 (v02 DELL PE_SC3 00000001 DELL 00000001)
ACPI: SSDT 0xbf6c7000 02164 (v01 INTEL PPM RCM 80000001 INTL 20061109)
MADT: Found IO APIC ID 0, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
lapic: Routing NMI -> LINT1
lapic: LINT1 trigger: edge
lapic: LINT1 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
wlan: <802.11 Link Layer>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
acpi0: <DELL PE_SC3> on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
unknown: I/O range not supported
ACPI timer: 1/1 1/2 1/2 1/2 1/1 1/1 1/2 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 15 N 0 3 4 5 6 7 10 11 14 15
Validation 0 15 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 10 11 14 15
Validation 0 10 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 6 N 0 3 4 5 6 7 10 11 14 15
Validation 0 6 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 10 11 14 15
Validation 0 11 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 14 N 0 3 4 5 6 7 10 11 14 15
Validation 0 14 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 10 11 14 15
Validation 0 255 N 0 3 4 5 6 7 10 11 14 15
After Disable 0 255 N 0 3 4 5 6 7 10 11 14 15
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0xd130, revid=0x11
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 3 supports D0 D3 current D0
MSI supports 2 messages, vector masks
found-> vendor=0x8086, dev=0xd138, revid=0x11
domain=0, bus=0, slot=3, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 3 supports D0 D3 current D0
MSI supports 2 messages, vector masks
found-> vendor=0x8086, dev=0xd155, revid=0x11
domain=0, bus=0, slot=8, func=0
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0xd156, revid=0x11
domain=0, bus=0, slot=8, func=1
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0xd157, revid=0x11
domain=0, bus=0, slot=8, func=2
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0xd158, revid=0x11
domain=0, bus=0, slot=8, func=3
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0xd150, revid=0x11
domain=0, bus=0, slot=16, func=0
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0xd151, revid=0x11
domain=0, bus=0, slot=16, func=1
class=08-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3b3c, revid=0x05
domain=0, bus=0, slot=26, func=0
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=14
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xdf0fa000, size 10, enabled
pcib0: matched entry for 0.26.INTA
pcib0: slot 26 INTA hardwired to IRQ 22
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdf0fa000
ehci early: SMM active, request owner change
found-> vendor=0x8086, dev=0x3b42, revid=0x05
domain=0, bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
found-> vendor=0x8086, dev=0x3b34, revid=0x05
domain=0, bus=0, slot=29, func=0
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=14
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xdf0fc000, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 22
unknown: Reserved 0x400 bytes for rid 0x10 type 3 at 0xdf0fc000
found-> vendor=0x8086, dev=0x244e, revid=0xa5
domain=0, bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3b14, revid=0x05
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x3b22, revid=0x05
domain=0, bus=0, slot=31, func=2
class=01-06-01, hdrtype=0x00, mfdev=0
cmdreg=0x0047, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 3 supports D0 D3 current D0
MSI supports 1 message
map[10]: type I/O Port, range 32, base 0xecd0, size 3, enabled
map[14]: type I/O Port, range 32, base 0xecc8, size 2, enabled
map[18]: type I/O Port, range 32, base 0xecd8, size 3, enabled
map[1c]: type I/O Port, range 32, base 0xeccc, size 2, enabled
map[20]: type I/O Port, range 32, base 0xece0, size 5, enabled
map[24]: type Memory, range 32, base 0xdf0fe000, size 11, enabled
pcib0: matched entry for 0.31.INTA
pcib0: slot 31 INTA hardwired to IRQ 20
pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xffff
pcib1: memory decode 0xdf100000-0xdf2fffff
pcib1: no prefetched decode
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1000, dev=0x0072, revid=0x02
domain=0, bus=1, slot=0, func=0
class=01-07-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 3 supports D0 D1 D2 D3 current D0
MSI supports 1 message, 64 bit
MSI-X supports 15 messages in map 0x14
map[10]: type I/O Port, range 32, base 0xfc00, size 8, enabled
pcib1: requested I/O range 0xfc00-0xfcff: in range
map[14]: type Memory, range 64, base 0xdf2b0000, size 16, enabled
pcib1: requested memory range 0xdf2b0000-0xdf2bffff: good
map[1c]: type Memory, range 64, base 0xdf2c0000, size 18, enabled
pcib1: requested memory range 0xdf2c0000-0xdf2fffff: good
pcib1: matched entry for 1.0.INTA
pcib1: slot 0 INTA hardwired to IRQ 16
mps0: <LSI SAS2008> port 0xfc00-0xfcff mem
0xdf2b0000-0xdf2bffff,0xdf2c0000-0xdf2fffff irq 16 at device 0.0 on pci1
mps0: Reserved 0x10000 bytes for rid 0x14 type 3 at 0xdf2b0000
mps0: Firmware: 02.15.57.00
mps0: IOCCapabilities:
185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
mps0: attempting to allocate 1 MSI-X vectors (15 supported)
msi: routing MSI-X IRQ 256 to local APIC 0 vector 49
mps0: using IRQ 256 for MSI-X
mps0: [MPSAFE]
mps0: [ITHREAD]
pci0: <base peripheral> at device 8.0 (no driver attached)
pci0: <base peripheral> at device 8.1 (no driver attached)
pci0: <base peripheral> at device 8.2 (no driver attached)
pci0: <base peripheral> at device 8.3 (no driver attached)
pci0: <base peripheral> at device 16.0 (no driver attached)
pci0: <base peripheral> at device 16.1 (no driver attached)
ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xdf0fa000-0xdf0fa3ff
irq 22 at device 26.0 on pci0
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 50
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus0: EHCI version 1.0
usbus0: <Intel PCH USB 2.0 controller USB-B> on ehci0
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xda000000-0xddffffff
pcib2: no prefetched decode
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x14e4, dev=0x163b, revid=0x20
domain=0, bus=2, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 3 supports D0 D3 current D0
MSI supports 16 messages, 64 bit
MSI-X supports 9 messages in map 0x10
map[10]: type Memory, range 64, base 0xda000000, size 25, enabled
pcib2: requested memory range 0xda000000-0xdbffffff: good
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x14e4, dev=0x163b, revid=0x20
domain=0, bus=2, slot=0, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
powerspec 3 supports D0 D3 current D0
MSI supports 16 messages, 64 bit
MSI-X supports 9 messages in map 0x10
map[10]: type Memory, range 64, base 0xdc000000, size 25, enabled
pcib2: requested memory range 0xdc000000-0xddffffff: good
pcib2: matched entry for 2.0.INTB
pcib2: slot 0 INTB hardwired to IRQ 17
bce0: <Broadcom NetXtreme II BCM5716 1000Base-T (C0)> mem
0xda000000-0xdbffffff irq 16 at device 0.0 on pci2
bce0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xda000000
bce0: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 64
bce0: using IRQ 257 for MSI
miibus0: <MII bus> on bce0
brgphy0: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: OUI 0x0050ef, model 0x003c, rev. 8
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce0: bpf attached
bce0: Ethernet address: 00:26:b9:7e:83:71
bce0: [MPSAFE]
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Flags (MSI|MFW); MFW (NCSI 2.0.5)
bce1: <Broadcom NetXtreme II BCM5716 1000Base-T (C0)> mem
0xdc000000-0xddffffff irq 17 at device 0.1 on pci2
bce1: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xdc000000
bce1: attempting to allocate 1 MSI vectors (16 supported)
msi: routing MSI IRQ 258 to local APIC 0 vector 80
bce1: using IRQ 258 for MSI
miibus1: <MII bus> on bce1
brgphy1: <BCM5709C 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: OUI 0x0050ef, model 0x003c, rev. 8
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bce1: bpf attached
bce1: Ethernet address: 00:26:b9:7e:83:72
bce1: [MPSAFE]
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.0.11);
Flags (MSI|MFW); MFW (NCSI 2.0.5)
ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xdf0fc000-0xdf0fc3ff
irq 22 at device 29.0 on pci0
ehci1: [MPSAFE]
ehci1: [ITHREAD]
usbus1: EHCI version 1.0
usbus1: <Intel PCH USB 2.0 controller USB-A> on ehci1
pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xf000-0xfff
pcib3: memory decode 0xde000000-0xdeffffff
pcib3: prefetched decode 0xd9800000-0xd9ffffff
pcib3: Subtractively decoded bridge.
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
found-> vendor=0x102b, dev=0x0532, revid=0x0a
domain=0, bus=3, slot=3, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=16 (dwords)
lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=6
powerspec 1 supports D0 D3 current D0
map[10]: type Prefetchable Memory, range 32, base 0xd9800000,
size 23, enabled
pcib3: requested memory range 0xd9800000-0xd9ffffff: good
map[14]: type Memory, range 32, base 0xde7fc000, size 14, enabled
pcib3: requested memory range 0xde7fc000-0xde7fffff: good
map[18]: type Memory, range 32, base 0xde800000, size 23, enabled
pcib3: requested memory range 0xde800000-0xdeffffff: good
pcib3: matched entry for 3.3.INTA
pcib3: slot 3 INTA hardwired to IRQ 19
vgapci0: <VGA-compatible display> mem
0xd9800000-0xd9ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19
at device 3.0 on pci3
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 5 Series/3400 Series PCH SATA300 controller> port
0xecd0-0xecd7,0xecc8-0xeccb,0xecd8-0xecdf,0xeccc-0xeccf,0xece0-0xecff
mem 0xdf0fe000-0xdf0fe7ff irq 20 at device 31.2 on pci0
atapci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xece0
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 0 vector 51
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: Reserved 0x800 bytes for rid 0x24 type 3 at 0xdf0fe000
atapci0: AHCI called from vendor specific driver
atapci0: AHCI v1.30 controller with 6 3Gbps ports, PM supported
atapci0: Caps: 64bit NCQ SNTF ALP AL CLO 3Gbps PM PMD SSC PSC 32cmd EM
eSATA 6ports
ata2: <ATA channel 0> on atapci0
ata2: AHCI reset...
ata2: hardware reset ...
ata2: SATA connect timeout status=00000000
ata2: AHCI reset done: phy reset found no device
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: AHCI reset...
ata3: hardware reset ...
ata3: SATA connect timeout status=00000000
ata3: AHCI reset done: phy reset found no device
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: AHCI reset...
ata4: hardware reset ...
ata4: SATA connect timeout status=00000000
ata4: AHCI reset done: phy reset found no device
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: AHCI reset...
ata5: hardware reset ...
ata5: SATA connect timeout status=00000000
ata5: AHCI reset done: phy reset found no device
ata5: [MPSAFE]
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: AHCI reset...
ata6: hardware reset ...
ata6: SATA connect timeout status=00000000
ata6: AHCI reset done: phy reset found no device
ata6: [MPSAFE]
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: AHCI reset...
ata7: hardware reset ...
ata7: SATA connect timeout status=00000000
ata7: AHCI reset done: phy reset found no device
ata7: [MPSAFE]
ata7: [ITHREAD]
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 8 hz: 14318180 opts: legacy_route
64-bit
Timecounter "HPET" frequency 14318180 Hz quality 900
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 52
uart0: [FILTER]
uart0: fast interrupt
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 0 vector 53
uart1: [FILTER]
uart1: fast interrupt
acpi0: wakeup code va 0xffffff847fa80000 pa 0x4000
ex_isa_identify()
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
isa_probe_children: disabling PnP devices
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
uart: uart0 already exists; skipping it
uart: uart1 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc8fff,0xec000-0xeffff on isa0
atkbd: the current kbd controller command byte 0065
atkbd: unable to set the command byte.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 54
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: unable to set the command byte.
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at irq 7 on isa0
isa_probe_children: probing PnP devices
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est4 attach returned 6
p4tcc4: <CPU Frequency Thermal Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est5 attach returned 6
p4tcc5: <CPU Frequency Thermal Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est6 attach returned 6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est7 attach returned 6
p4tcc7: <CPU Frequency Thermal Control> on cpu7
Device configuration finished.
procfs registered
ZFS filesystem version 5
ZFS storage pool version 28
lapic: Divisor 2, Frequency 66459680 Hz
Timecounter "TSC" frequency 1861998768 Hz quality -100
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
hptrr: no controller detected.
ata2: Identifying devices: 00000000
ata2: New devices: 00000000
ata3: Identifying devices: 00000000
ata3: New devices: 00000000
ata4: Identifying devices: 00000000
ata4: New devices: 00000000
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
ata6: Identifying devices: 00000000
ata6: New devices: 00000000
ata7: Identifying devices: 00000000
ata7: New devices: 00000000
md0: Preloaded image </mfsroot> 36282368 bytes at 0xffffffff810b9920
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2>
on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2>
on usbus1
mps0: Found device <881<SataDev,Direct>,End Device> <3.0Gbps> <0x0009> <1/1>
mps0: Found device <881<SataDev,Direct>,End Device> <3.0Gbps> <0x000a> <1/0>
uhub2: 6 ports with 6 removable, self powered
uhub3: 8 ports with 8 removable, self powered
ugen0.3: <Avocent> at usbus0
ukbd0: <Keyboard> on usbus0
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ums0: <Mouse> on usbus0
ums0: 3 buttons and [Z] coordinates ID=0
ugen1.3: <vendor 0x0424> at usbus1
uhub4: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/0.00, addr 3>
on usbus1
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
(probe1:mps0:0:1:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Down reving Protocol Version from 4 to 2?
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe0:mps0:0:0:0): Down reving Protocol Version from 4 to 2?
(probe1:mps0:0:1:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Down reving Protocol Version from 4 to 2?
(probe0:mps0:0:0:0): Error 22, Unretryable error
(probe1:mps0:0:1:0): Error 22, Unretryable error
uhub4: 4 ports with 4 removable, self powered
ATA PseudoRAID loaded
llaappicicl32al:p alCi:palpiaip iccCcc6M457M:CC:II: : uuCnnmmCa
aMCCssMkMkeedCdICCI I uMunCm naumIassk enkudmnaesmdkaesdked
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000100f2
SMP: AP CPU #7 Launched!
cpu7 AP:
ID: 0x07000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #5 Launched!
cpu5 AP:
ID: 0x05000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #6 Launched!
cpu6 AP:
ID: 0x06000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #4 Launched!
cpu4 AP:
ID: 0x04000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #3 Launched!
cpu3 AP:
ID: 0x03000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
SMP: AP CPU #2 Launched!
cpu2 AP:
ID: 0x02000000 VER: 0x00060015 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
cmci: 0x000000f2
ioapic0: routing intpin 3 (ISA IRQ 3) to lapic 1 vector 48
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 2 vector 48
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 3 vector 48
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 4 vector 48
ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 5 vector 48
msi: Assigning MSI-X IRQ 256 to local APIC 6 vector 48
msi: Assigning MSI IRQ 257 to local APIC 7 vector 48
Trying to mount root from ufs:/dev/md0
start_init: trying /sbin/init
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4D46A276.60304>