Date: 04 Oct 2005 20:49:42 -0400 From: Lowell Gilbert <freebsd-questions-local@be-well.ilk.org> To: freebsd-questions@freebsd.org Subject: Re: 5.4 reboots when I plug in a flash drive? Message-ID: <44achoiy8p.fsf@be-well.ilk.org> In-Reply-To: <43431D86.40903@fusemail.com> References: <1468.209.87.176.132.1128439684.fusewebmail-19592@webmail.fusemail.com > <20051005000110.GA51496@holestein.holy.cow> <43431D86.40903@fusemail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Brian John <brianjohn@fusemail.com> writes: > Parv wrote: > > >in message > ><1468.209.87.176.132.1128439684.fusewebmail-19592@webmail.fusemail.com > > > >>, wrote Brian John thusly... > >> > >>I just got a 128MB USB flash drive. When I plug it in in FreeBSD, > >>the box promptly reboots! What would cause this? > >> > > > >I don't know the cause. > > > >Have you tried booting FreeBSD from power-off state w/ the flash > >drive already inserted? That may solve your booting problem, but > >will not make use of the drive any easier. > > > >Which version if FreeBSD are you using? Which of the [ueo]hci > >drivers come up in dmesg(8) on instertion of the USB drive? > > > > > > - Parv > > > > > Ok, I tried booting up with the drive installed. If I leave it > installed while it is booting up, it eventually reboots. However, I > was able to unplug it during boot and look at dmesg. It says this > over and over again: > > umass0: vendor 0x10d6 USB 2.0(FS) FLASH DISK, rev 1.10/1.00, addr 2 > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <USB2.0 (FS) FLASH DISK 1.00> Removable Direct Access SCSI-0 device > da0: 1.000MB/s transfers > da0: 119MB (245473 512 byte sectors: 64H 32S/T 119C) > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > (da0:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi > status == 0x0 > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > umass0: BBB reset failed, STALLED > umass0: BBB bulk-in clear stall failed, STALLED > umass0: BBB bulk-out clear stall failed, STALLED > umass0: at uhub2 port 1 (addr 2) disconnected > (da0:umass-sim0:0:0:0): lost device > (da0:umass-sim0:0:0:0): removing device entry > Opened disk da0 -> 5 > umass0: detached > > I am running FreeBSD 5.4. Does this shed some light on the problem? Only a little. Do you have udbp(4) in your kernel? Can you try booting 6.0 with the flash unit plugged in and see if it still has problems?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?44achoiy8p.fsf>