Date: Mon, 13 May 2002 13:52:48 +0200 From: "Simon L. Nielsen" <simon@nitro.dk> To: freebsd-stable@FreeBSD.ORG Subject: SMP problems with Fujitsu Siemens Primergy P200 Message-ID: <20020513115248.GA34034@nitro.dk>
next in thread | raw e-mail | index | archive | help
Hello
I'm having some problems using SMP on a Fujitsu Siemens Primergy P200
with FreeBSD 4.5-RELEASE-p4. It's a dual Intel Pentium 3 1266MHz with
1GB ECC RAM. It has a Mylex AcceleRAID 352 controller connected to 4
SCSI disks, and a normal ATAPI CD-ROM drive. It also has a on-board
Symbios SCSI controller but this is not being used at present.
When booting a SMP kernel it simply hangs after initializing the
second CPU. The computer is not completely frozen since I can break
to the kernel debugger, but it never gets any further.
However, I don't really have enough information about the internals of
the kernel to do anything useful in the kernel debugger...
The computer works fine on a single CPU kernel. I have also tried to
boot on another computer with the exact same hardware and still there
is no positive result, so it would not appear to be "normal" defective
hardware.
I have tried booting a 4.6-PRERELEASE (from today) and 5.0DP1 without
success. The 4.6 fails in the same way as 4.5, but it does detect the
CD-ROM drive after it has written "AP CPU #1 Launched" (I have not
included the output since it is almost the same and rather large). The
5.0DP1 just does a kernel after detecting the Mylex controller but I
don't think that is really related to the main problem.
I have included output from from a verbose boot and output from
mptable.
Any hints on what might be wrong or suggestions how to fix the problem
would be very much appreciated.
Verbose boot message from 4.5-RELEASE-p4 :
SMAP type=01 base=00000000 00000000 len=00000000 0009e400
SMAP type=02 base=00000000 0009e400 len=00000000 00001c00
SMAP type=02 base=00000000 000ca000 len=00000000 00002000
SMAP type=02 base=00000000 000e0000 len=00000000 00020000
SMAP type=01 base=00000000 00100000 len=00000000 3fdf0000
SMAP type=03 base=00000000 3fef0000 len=00000000 0000f000
SMAP type=04 base=00000000 3feff000 len=00000000 00001000
SMAP type=01 base=00000000 3ff00000 len=00000000 00100000
SMAP type=02 base=00000000 fec00000 len=00000000 00010000
SMAP type=02 base=00000000 fee00000 len=00000000 00001000
SMAP type=02 base=00000000 ffc00000 len=00000000 00400000
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-RELEASE-p4 #2: Fri May 10 23:01:17 GST 2002
root@hd1.test.siemens.com:/usr/src/sys/compile/DEM-HARVESTER2
Calibrating clock(s) ... TSC clock: 1260490417 Hz, i8254 clock: 1193080 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon/Celeron (1260.61-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073741824 (1048576K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009dfff, 643072 bytes (157 pages)
0x004db000 - 0x3feeffff, 1067536384 bytes (260629 pages)
0x3ff00000 - 0x3fff7fff, 1015808 bytes (248 pages)
avail memory = 1040273408 (1015892K bytes)
Programming 16 pins in IOAPIC #0
Programming 16 pins in IOAPIC #1
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 1, version: 0x000f0011, at 0xfec00000
io1 (APIC): apic id: 2, version: 0x000f0011, at 0xfec01000
bios32: Found BIOS32 Service Directory header at 0xc00f6ba0
bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x11a
pnpbios: Found PnP BIOS data at 0xc00f6c30
pnpbios: Entry = f0000:9dd0 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f6c00
Preloaded elf kernel "kernel.old" at 0xc04b1000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000270
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00081166)
Using $PIR table, 15 entries at 0xc00fded0
pcib-: pcib1 exists, using next available unit number
pcib-: pcib2 exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib1: <ServerWorks host to PCI bridge> on motherboard
IOAPIC #1 intpin 13 -> irq 5
Freeing (NOT implemented) redirected PCI irq 10.
found-> vendor=0x1000, dev=0x0021, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
pci1: <PCI bus> on pcib1
sym0: <1010-66> irq 5 at device 10.0 on pci1
sym0: failed to allocate MMIO resources
device_probe_and_attach: sym0 attach returned 6
pcib0: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x1166, dev=0x0008, revid=0x23
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0008, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1002, dev=0x4752, revid=0x27
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f5000000, size 24
map[14]: type 1, range 32, base 00001000, size 8
map[18]: type 1, range 32, base f4020000, size 12
IOAPIC #1 intpin 14 -> irq 9
Freeing (NOT implemented) redirected PCI irq 11.
found-> vendor=0x8086, dev=0x1229, revid=0x09
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base f4021000, size 12
map[14]: type 1, range 32, base 00001400, size 6
map[18]: type 1, range 32, base f4000000, size 17
found-> vendor=0x1166, dev=0x0200, revid=0x51
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0211, revid=0x00
class=01-01-8a, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00001800, size 4
IOAPIC #1 intpin 12 -> irq 10
Freeing (NOT implemented) redirected PCI irq 9.
found-> vendor=0x1166, dev=0x0220, revid=0x04
class=0c-03-10, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base f4022000, size 12
pci0: <PCI bus> on pcib0
pci0: <ATI Mach64-GR graphics accelerator> (vendor=0x1002, dev=0x4752) at 4.0
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1400-0x143f mem 0xf4000000-0xf401ffff,0xf4021000-0xf4021fff irq 9 at device 10.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:30:05:29:07:61
fxp0: PCI IDs: 8086 1229 110a 004b 0009
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x1800-0x180f at device 15.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1800
ata0: mask=03 status0=20 status1=30
ata0: mask=03 ostat0=20 ostat2=30
ata0-master: ATAPI probe a=20 b=20
ata0-slave: ATAPI probe a=30 b=30
ata0: mask=03 status0=20 status1=30
ata0-master: ATA probe a=25 b=25
ata0-slave: ATA probe a=25 b=25
ata0: devices=00
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1808
ata1: mask=03 status0=50 status1=00
ata1: mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI probe a=14 b=eb
ata1-slave: ATAPI probe a=14 b=eb
ata1: mask=03 status0=00 status1=00
ata1: devices=0c
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xf4022000-0xf4022fff irq 10 at device 15.2 on pci0
ohci0: (New OHCI DeviceId=0x02201166)
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib2: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x1011, dev=0x0026, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=3 secondarybus=3
IOAPIC #1 intpin 9 -> irq 11
found-> vendor=0x1069, dev=0x0050, revid=0x02
class=01-04-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base f8000000, size 26
pci2: <PCI bus> on pcib2
pcib4: <DEC 21154 PCI-PCI bridge> at device 10.0 on pci2
IOAPIC #1 intpin 11 -> irq 16
Freeing (NOT implemented) redirected PCI irq 5.
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=16
map[10]: type 1, range 32, base f6400000, size 19
map[14]: type 1, range 32, base 00002000, size 8
IOAPIC #1 intpin 8 -> irq 17
Freeing (NOT implemented) redirected PCI irq 9.
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=17
map[10]: type 1, range 32, base f6480000, size 19
map[14]: type 1, range 32, base 00002400, size 8
pci3: <PCI bus> on pcib4
sf0: <Adaptec ANA-62022 10/100BaseTX> port 0x2000-0x20ff mem 0xf6400000-0xf647ffff irq 16 at device 4.0 on pci3
sf0: Ethernet address: 00:00:d1:9d:b7:a4
miibus1: <MII bus> on sf0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: OUI 0x0005be, model 0x0003, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf0 attached
sf1: <Adaptec ANA-62022 10/100BaseTX> port 0x2400-0x24ff mem 0xf6480000-0xf64fffff irq 17 at device 5.0 on pci3
sf1: Ethernet address: 00:00:d1:9d:b7:a5
miibus2: <MII bus> on sf1
ukphy1: <Generic IEEE 802.3u media interface> on miibus2
ukphy1: OUI 0x0005be, model 0x0003, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf1 attached
mly0: <Mylex AcceleRAID 352> mem 0xf8000000-0xfbffffff irq 11 at device 12.0 on pci2
mly0: AcceleRAID 352 , 2 channels, firmware 6.00-17-00 (20020218), 64MB RAM
mly0: Siemens AcceleRAID 352 (1e), 33MHz 64-bit PCI
mly0: 64MB 66MHz 64-bit SDRAM+ECC, cache 56MB
mly0: CPU: i960RN @ 100MHZ
mly0: 4MB 66MHz 64-bit private SDRAM+ECC
mly0: battery backup not installed
mly0: maximum data transfer 2048 blocks, maximum sg entries/command 257
mly0: logical devices present/critical/offline 1/0/0
mly0: physical devices present 7
mly0: physical disks present/offline 4/0
mly0: 2 physical channels, 2 virtual channels of 2 possible
mly0: 512 parallel commands supported
mly0: 1MB flash ROM, 0 of 100000 maximum cycles
pci-: pci3 exists, using next available unit number
pcib3: <ServerWorks host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib3
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xcc7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 0a 03 c8
psm: status 0a 03 c8
psm: status 0a 03 c8
psm: status 0a 03 c8
psm: data 08 00 00
psm: status 0a 03 c8
psm: data 08 00 00
psm: status 0a 03 c8
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x8841 0x8851 0x8841 0x8841
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x8841 0x8849 0x8841 0x8841
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0
fe0 failed to probe at port 0x300-0x31f on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
cs0 failed to probe at port 0x300-0x31f on isa0
sn0 failed to probe at port 0x300-0x30f irq 10 on isa0
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 3, 4, 6, 7, 9, 10, 11, 12, 14, 15, 16, 17, apic_imen: 0x00fc2125
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: routing 8254 via IOAPIC #0 intpin 0
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 6800c440, tty 6300109a, net 6703129a
bpf: sl0 attached
bpf: faith0 attached
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
[END]
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f6c70
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x2f
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0009e880
signature: 'PCMP'
base table length: 300
version: 1.4
checksum: 0xb6
OEM ID: 'FSCD1306'
Product ID: 'PRIMERGY '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 29
local APIC address: 0xfee00000
extended table length: 236
extended table checksum: 156
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
3 0x11 BSP, usable 6 11 1 0x383fbff
0 0x11 AP, usable 6 11 1 0x383fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 PCI
3 PCI
4 ISA
--
I/O APICs: APIC ID Version State Address
1 0x11 usable 0xfec00000
2 0x11 usable 0xfec01000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
INT active-hi edge 4 0 1 0
INT active-hi edge 4 1 1 1
INT active-hi edge 4 2 1 2
INT active-hi edge 4 3 1 3
INT active-hi edge 4 4 1 4
INT active-hi edge 4 6 1 6
INT active-hi edge 4 7 1 7
INT active-hi edge 4 8 1 8
INT active-hi edge 4 12 1 12
INT active-hi edge 4 13 1 13
INT active-hi edge 4 14 1 14
INT active-hi edge 4 15 1 15
INT active-lo level 0 10:A 2 14
INT active-lo level 0 15:A 2 12
INT active-lo level 1 10:A 2 13
INT active-lo level 3 4:A 2 11
INT active-lo level 3 5:A 2 8
INT active-lo level 2 12:A 2 9
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 4 0 255 0
NMI active-hi edge 0 0:A 255 1
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0x0
address range: 0x1c00
--
System Address Space
bus ID: 1 address type: I/O address
address base: 0x1c00
address range: 0x100
--
System Address Space
bus ID: 0 address type: I/O address
address base: 0x1d00
address range: 0xe300
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xf4000000
address range: 0x2000000
--
System Address Space
bus ID: 1 address type: memory address
address base: 0xf6000000
address range: 0x3ff800
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xf63ff800
address range: 0x8a00800
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xfee01000
address range: 0x11ff000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xa0000
address range: 0x20000
--
System Address Space
bus ID: 0 address type: memory address
address base: 0xd0000
address range: 0x10000
--
Bus Heirarchy
bus ID: 4 bus info: 0x01 parent bus ID: 0
--
Compatibility Bus Address
bus ID: 0 address modifier: add
predefined range: 0x00000000
--
Compatibility Bus Address
bus ID: 0 address modifier: add
predefined range: 0x00000001
--
Compatibility Bus Address
bus ID: 1 address modifier: subtract
predefined range: 0x00000000
--
Compatibility Bus Address
bus ID: 1 address modifier: subtract
predefined range: 0x00000001
--
Compatibility Bus Address
bus ID: 2 address modifier: subtract
predefined range: 0x00000000
--
Compatibility Bus Address
bus ID: 2 address modifier: subtract
predefined range: 0x00000001
===============================================================================
--
Simon L. Nielsen
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020513115248.GA34034>