Date: Thu, 2 Mar 2000 04:09:40 -0800 (PST) From: Don Lewis <Don.Lewis@tsc.tdk.com> To: current@freebsd.org Subject: current hangs during boot if ET/5025-16 card is installed Message-ID: <200003021209.EAA05907@salsa.gv.tsc.tdk.com>
next in thread | raw e-mail | index | archive | help
I happened to try to install 4.0-CURRENT on a box that has an Emerging Technologies ET/5025-16 ISA card installed and found that the kernel wedges during boot. It hangs hard and won't respond to anything except the reset switch. The motherboard is an Asus P3B-F and I believe I have the BIOS propery configured with the correct settings to match the IRQ and memory addresses used by the ET card. I also discovered that older versions of -CURRENT will boot correctly on this box. I did a binary search on the -CURRENT snapshots and found that the floppies from the January 12th and earlier snapshots boot, while the floppies from the January 14th and later snapshots hang. Here's the dmesg.boot file that I get by doing a "boot -v" with using late January kernel with the offending card removed. With the card installed, the boot process gets as far as Trying Read_Port at 3c3 but doesn't get to isa_probe_children: disabling PnP devices drtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[20]: type 1, range 32, base 0000d800, size 4 found-> vendor=0x8086, dev=0x7112, revid=0x01 class=0c-03-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=d, irq=255 map[20]: type 1, range 32, base 0000d400, size 5 found-> vendor=0x8086, dev=0x7113, revid=0x02 class=06-80-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 map[90]: type 1, range 32, base 0000e800, size 4 found-> vendor=0x8086, dev=0x1229, revid=0x08 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=9 map[10]: type 1, range 32, base e1800000, size 12 map[14]: type 1, range 32, base 0000d000, size 6 map[18]: type 1, range 32, base e1000000, size 20 found-> vendor=0x8086, dev=0x1229, revid=0x08 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=15 map[10]: type 1, range 32, base e0800000, size 12 map[14]: type 1, range 32, base 0000b800, size 6 map[18]: type 1, range 32, base e0000000, size 20 found-> vendor=0x8086, dev=0x1229, revid=0x08 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[10]: type 1, range 32, base df800000, size 12 map[14]: type 1, range 32, base 0000b400, size 6 map[18]: type 1, range 32, base df000000, size 20 found-> vendor=0x8086, dev=0x1229, revid=0x08 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base de800000, size 12 map[14]: type 1, range 32, base 0000b000, size 6 map[18]: type 1, range 32, base de000000, size 20 pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 found-> vendor=0x104c, dev=0x3d07, revid=0x01 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=11 map[10]: type 1, range 32, base e3000000, size 17 map[14]: type 1, range 32, base e2800000, size 23 map[18]: type 1, range 32, base e2000000, size 23 pci1: <PCI bus> on pcib1 vga-pci0: <VGA-compatible display device> mem 0xe2000000-0xe27fffff,0xe2800000-0xe2ffffff,0xe3000000-0xe301ffff irq 11 at device 0.0 on pci1 isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0 isa0: <ISA bus> on isab0 ata-pci0: <Intel PIIX4 ATA-33 controller> port 0xd800-0xd80f at device 4.1 on pci0 ata-pci0: Busmastering DMA supported ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd800 ata0: mask=03 status0=50 status1=50 ata0: mask=03 status0=50 status1=00 ata0: devices = 0x9 ata0 at 0x01f0 irq 14 on ata-pci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd808 ata1: mask=00 status0=ff status1=ff pci0: Intel 82371AB/EB (PIIX4) USB controller (vendor=0x8086, dev=0x7112) at 4.2 chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at device 4.3 on pci0 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> port 0xd000-0xd03f mem 0xe1000000-0xe10fffff,0xe1800000-0xe1800fff irq 9 at device 9.0 on pci0 fxp0: Ethernet address 00:90:27:c6:bb:b8 bpf: fxp0 attached fxp1: <Intel EtherExpress Pro 10/100B Ethernet> port 0xb800-0xb83f mem 0xe0000000-0xe00fffff,0xe0800000-0xe0800fff irq 15 at device 10.0 on pci0 fxp1: Ethernet address 00:90:27:c6:bc:b9 bpf: fxp1 attached fxp2: <Intel EtherExpress Pro 10/100B Ethernet> port 0xb400-0xb43f mem 0xdf000000-0xdf0fffff,0xdf800000-0xdf800fff irq 10 at device 11.0 on pci0 fxp2: Ethernet address 00:90:27:c6:bc:c0 bpf: fxp2 attached fxp3: <Intel EtherExpress Pro 10/100B Ethernet> port 0xb000-0xb03f mem 0xde000000-0xde0fffff,0xde800000-0xde800fff irq 11 at device 12.0 on pci0 fxp3: Ethernet address 00:90:27:c6:a6:12 bpf: fxp3 attached Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices fe0: not probed (disabled) fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata-isa0: already registered as ata0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000 ata1: mask=00 status0=ff status1=ff adv0: not probed (disabled) bt0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 psm0: current command byte:0047 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 00 00 64 psm: status 00 03 64 psm: status 00 03 64 psm: status 10 00 64 psm: data 08 00 00 psm: status 00 02 64 psm: data 08 00 00 psm: status 00 02 64 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 6f 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 6f 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) pcic1: not probed (disabled) sio0: irq maps: 0x41 0x51 0x41 0x41 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: irq maps: 0x41 0x49 0x41 0x41 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A sio2: not probed (disabled) sio3: not probed (disabled) ppc0: parallel port found at 0x378 ppc0: ECP SPP ECP+EPP SPP ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port plip0: <PLIP network interface> on ppbus0 bpf: lp0 attached ppi0: <Parallel I/O> on ppbus0 ed0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) cs0: not probed (disabled) isa_probe_children: probing PnP devices BIOS Geometries: 0:026c3f3f 0..620=621 cylinders, 0..63=64 heads, 1..63=63 sectors 0 accounted for Device configuration finished. bpf: sl0 attached bpf: ppp0 attached new masks: bio 40084040, tty 4003109a, net 40079e9a bpf: lo0 attached ata0-master: success setting up PIO3 mode on generic chip ad0: piomode=3 dmamode=1 udmamode=-1 cblid=0 ad0: <WDC AC31200F/14.04E2> ATA-0 disk at ata0 as master ad0: 1222MB (2503872 sectors), 2484 cyls, 16 heads, 63 S/T, 512 B/S ad0: 16 secs/int, 1 depth queue, PIO3 Creating DISK ad0 Creating DISK wd0 ata0-slave: piomode=4 dmamode=2 udmamode=2 dmaflag=1 ata0-slave: success setting up PIO4 mode on generic chip acd0: <TOSHIBA CD-ROM XM-6602B/1017> CDROM drive at ata0 as slave acd0: read 6890KB/s (6890KB/s), 128KB buffer, PIO4 acd0: Reads: CD-R, CD-RW, CD-DA stream acd0: Audio: play, 16 volume levels acd0: Mechanism: ejectable tray acd0: Medium: no/blank disc inside, unlocked Mounting root from ufs:/dev/ad0s1a ad0s1: type 0xa5, start 63, end = 2503871, size 2503809 : OK start_init: trying /sbin/init To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200003021209.EAA05907>