Date: Mon, 25 Feb 2002 16:56:01 -0800 (PST) From: Vinod <geekvinod@yahoo.com> To: freebsd-questions@freebsd.org Subject: watchdog timeout and setup problems with orinoco Message-ID: <20020226005601.49091.qmail@web21105.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
Hi there.I have been trying to install a orinoco gold
card with PCI adapter on a desktop running freebsd
4.4.
Everything worked fine as in the LED's look ok.But
when i ifconfig it i get watchdog timeouts.note that
this is the only time i get watchdog
timeouts.wicontrol works fine.
I am posting my dmesg below.Hoping for some help.
-------------------------------------------------------
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
1991, 1992, 1993,
1994
The Regents of the University of California. All
rights reserved.
FreeBSD 4.4-RELEASE #0: Wed Feb 20 14:03:58 EST 2002
root@coit2.uncc.edu:/usr/src/sys/compile/NEWKERN
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (266.62-MHz
686-class CPU)
Origin = "GenuineIntel" Id = 0x633 Stepping = 3
Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 67108864 (65536K bytes)
avail memory = 60432384 (59016K bytes)
Preloaded elf kernel "kernel" at 0xc04cd000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00fdf50
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> on
motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443LX (440 LX) PCI-PCI (AGP) bridge>
at device 1.0 on
pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0
on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port
0xfcd0-0xfcdf at device
7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port
0xfce0-0xfcff irq
9 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on
uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub0: 2 ports with 2 removable, self powered
chip1: <Intel 82371AB Power management controller>
port 0x7000-0x700f
at device 7.3 on pci0
pci0: <ATI Mach64-GU graphics accelerator> at 13.0
tx0: <SMC EtherPower II 10/100> port 0xf400-0xf4ff mem
0xfedfe000-0xfedfefff irq 11 at device 14.0 on pci0
miibus0: <MII bus> on tx0
qsphy0: <QS6612 10/100 media interface> on miibus0
qsphy0: 10baseT, 10baseT-FDX, 100baseTX,
100baseTX-FDX, auto
tx0: address 00:e0:29:11:6d:85, type SMC9432TX
pcm0: <AudioPCI ES1371-A> port 0xfc40-0xfc7f irq 10 at
device 15.0 on
pci0
pci_cfgintr_search: linked (63) to configured irq 10
at 0:15:0
pci_cfgintr: 0:16 INTA routed to irq 10
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 10 at
device 16.0 on pci0
pcic0: PCI Memory allocated: 0x44000000
pcic0: TI12XX PCI Config Reg: [pwr save][FUNC pci int
+ CSC serial isa
irq]
pccard0: <PC Card bus (classic)> on pcic0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xe8000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7
irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port
0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on
isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 4112MB <WDC AC24300L> [8912/15/63] at ata0-master
UDMA33
acd0: CDROM <TOSHIBA CD-ROM XM-6102B> at ata1-master
using PIO3
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 0
wi0: <WaveLAN/IEEE 802.11> at port 0x100-0x13f irq 10
slot 0 on pccard0
wi0: Ethernet address: 00:02:2d:3c:66:c2
wi0: watchdog timeout
-------------------------------------------------------
I even tried changing the port address(this is the new
range).no luck.
since i was getting watchdog timeouts only when i do
ifconfig (ifconfig looks fine too.accepts the
ipaddr).i thought maybe something else is
wrong.strangely my wi0 card links up with another 3com
pci card(ad-hoc mode,same channel,same ssid) when its
in IBSS mode but i cant ping between them.But when i
put my wi0 card in ad-hoc mode their link breaks.
i am attaching my ibss ifconfig,ibss wicontrol,adhoc
ifconfig,adhoc wicontrol below.hope somebody can put
some light.
------------------------------------------------------
ibss ifconfig
---------------
tx0:
flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu
1500
inet6 fe80::2e0:29ff:fe11:6d85%tx0 prefixlen 64
scopeid 0x1
inet 152.15.24.239 netmask 0xffffff00 broadcast
152.15.24.255
ether 00:e0:29:11:6d:85
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu
1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu
16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
faith0: flags=8000<MULTICAST> mtu 1500
wi0:
flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu
1500
inet6 fe80::202:2dff:fe3c:66c2%wi0 prefixlen 64
scopeid 0x7
inet 10.0.0.1 netmask 0xffffff00 broadcast 10.0.0.255
ether 00:02:2d:3c:66:c2
media: IEEE 802.11 Wireless Ethernet autoselect
(DS/2Mbps)
status: no carrier
ssid 101
stationname "FreeBSD WaveLAN/IEEE node"
channel 10 authmode NONE powersavemode OFF
powersavesleep 100
wepmode OFF weptxkey 1
----------------
ibss wicontrol
----------------
NIC serial number: [ 01UT36369401 ]
Station name: [ FreeBSD WaveLAN/IEEE node ]
SSID for IBSS creation: [ FreeBSD IBSS ]
Current netname (SSID): [ 101 ]
Desired netname (SSID): [ 101 ]
Current BSSID: [ f2:f3:ea:05:b4:a7 ]
Channel list: [ 2047 ]
IBSS channel: [ 10 ]
Current channel: [ 10 ]
Comms quality/signal/noise: [ 0 27 27 ]
Promiscuous mode: [ Off ]
Port type (1=BSS, 3=ad-hoc): [ 1 ]
MAC address: [ 00:02:2d:3c:66:c2 ]
TX rate (selection): [ 3 ]
TX rate (actual speed): [ 2 ]
RTS/CTS handshake threshold: [ 2347 ]
Create IBSS: [ On ]
Access point density: [ 1 ]
Power Mgmt (1=on, 0=off): [ 0 ]
Max sleep time: [ 100 ]
WEP encryption: [ Off ]
TX encryption key: [ 1 ]
Encryption keys: [ ][ ][ ][ ]
----------------
ad-hoc ifconfig
------------------
tx0:
flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu
1500
inet6 fe80::2e0:29ff:fe11:6d85%tx0 prefixlen 64
scopeid 0x1
inet 152.15.24.239 netmask 0xffffff00 broadcast
152.15.24.255
ether 00:e0:29:11:6d:85
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu
1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu
16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
faith0: flags=8000<MULTICAST> mtu 1500
wi0:
flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu
1500
inet6 fe80::202:2dff:fe3c:66c2%wi0 prefixlen 64
scopeid 0x7
inet 10.0.0.1 netmask 0xff000000 broadcast
10.255.255.255
ether 00:02:2d:3c:66:c2
media: IEEE 802.11 Wireless Ethernet autoselect
(DS/2Mbps <adhoc>)
status: associated
ssid "FreeBSD IBSS"
stationname "FreeBSD WaveLAN/IEEE node"
channel 10 authmode NONE powersavemode OFF
powersavesleep 100
wepmode OFF weptxkey 1
---------------------
ad-hoc wicontrol
----------------------
NIC serial number: [ 01UT36369401 ]
Station name: [ FreeBSD WaveLAN/IEEE node ]
SSID for IBSS creation: [ FreeBSD IBSS ]
Current netname (SSID): [ FreeBSD IBSS ]
Desired netname (SSID): [ 101 ]
Current BSSID: [ 00:00:00:00:00:00 ]
Channel list: [ 2047 ]
IBSS channel: [ 10 ]
Current channel: [ 10 ]
Comms quality/signal/noise: [ 0 27 27 ]
Promiscuous mode: [ Off ]
Port type (1=BSS, 3=ad-hoc): [ 3 ]
MAC address: [ 00:02:2d:3c:66:c2 ]
TX rate (selection): [ 3 ]
TX rate (actual speed): [ 2 ]
RTS/CTS handshake threshold: [ 2347 ]
Create IBSS: [ Off ]
Access point density: [ 1 ]
Power Mgmt (1=on, 0=off): [ 0 ]
Max sleep time: [ 100 ]
WEP encryption: [ Off ]
TX encryption key: [ 1 ]
Encryption keys: [ ][ ][ ][ ]
-------------------------------------------------------
Hope somebody can help me out.
Vinod
__________________________________________________
Do You Yahoo!?
Yahoo! Sports - Coverage of the 2002 Olympic Games
http://sports.yahoo.com
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020226005601.49091.qmail>