Date: Sun, 28 Aug 2005 11:13:05 -0400 (EDT) From: "Gary D. Margiotta" <gary@tbe.net> To: Robert Ken Francis <rkfrancis1@adelphia.net> Cc: freebsd-hardware@freebsd.org Subject: Re: Adaptec ATA RAID 1200A card supported? Message-ID: <20050828110352.S43725@kerplunk.tbe.net> In-Reply-To: <000801c5abdb$e25c1440$0a2e567e@monster4c> References: <000801c5abdb$e25c1440$0a2e567e@monster4c>
next in thread | previous in thread | raw e-mail | index | archive | help
The card itself is supported fine, the box I'm composing this mail from is using solely an Adaptec 1200A card, running 5-STABLE (which was originally installed with 5.2.1, and have been tracking -STABLE since). I don't see the Adaptec card getting probed in your dmesg... I see the onboard SiS controller (atapci0 with ata0 and ata1), and a HighPoint card (atapci1 with ata-2 and ata-3), and the errors I see are coming from the ata-2 and ata-3 channels, which are on the HighPoint controller. -Gary On Sun, 28 Aug 2005, Robert Ken Francis wrote: > I have failures like the below: > > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=4<ABORTED> > > What do I do to fix these failures? All of the "FAILURE" drives are on my Adaptec ATA RAID 1200A card. My secondary built-in IDE > is dead so I have to use this card as an IDE replacement. > > Thanks, > Rob > > Note that NetBSD doesn't have this problem. > > > Here is my dmesg: > > Copyright (c) 1992-2005 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. FreeBSD 5.4-RELEASE #0: Sun May 8 10:21:06 UTC 2005 > root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > ACPI APIC Table: <ASUS P4SP-MX > > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Celeron(R) CPU 2.40GHz (2400.18-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HT > T,TM,PBE> > real memory = 1040171008 (991 MB) > avail memory = 1008295936 (961 MB) > ioapic0 <Version 8.0> irqs 0-23 on motherboard > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <ASUS P4SP-MX> on motherboard > acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20 > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <SiS 651 host to AGP bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 2.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <SiS 962 UDMA133 controller> port 0xa400-0xa40f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 16 at device 2.5 on pci0 > ata0: channel #0 on atapci0 > ata1: channel #1 on atapci0 > ohci0: <SiS 5571 USB controller> mem 0xe7000000-0xe7000fff irq 20 at device 3.0 on pci0 > usb0: OHCI version 1.0, legacy support > usb0: <SiS 5571 USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > ohci1: <SiS 5571 USB controller> mem 0xe6800000-0xe6800fff irq 21 at device 3.1 on pci0 > usb1: OHCI version 1.0, legacy support > usb1: <SiS 5571 USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 3 ports with 3 removable, self powered > pci0: <serial bus, USB> at device 3.3 (no driver attached) > sis0: <SiS 900 10/100BaseTX> port 0x8800-0x88ff mem 0xe5800000-0xe5800fff irq 19 at device 4.0 on pci0 > miibus0: <MII bus> on sis0 > rlphy0: <RTL8201L 10/100 media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis0: Ethernet address: 00:0e:a6:98:41:8b > atapci1: <HighPoint HPT370 UDMA100 controller> port 0x7000-0x70ff,0x7400-0x7403,0x7800-0x7807,0x8000-0x8003,0x8400-0x8407 irq 17 at > device 14.0 on pci0 > ata2: channel #0 on atapci1 > ata3: channel #1 on atapci1 > pci0: <multimedia, audio> at device 16.0 (no driver attached) > fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/16 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio0: type 16550A > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > orm0: <ISA Option ROMs> at iomem 0xcc000-0xd07ff,0xc0000-0xcbfff on isa0 pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 2400181916 Hz quality 800 > Timecounters tick every 10.000 msec > ad0: 117246MB <Maxtor 6Y120L0/YAR41VW0> [238216/16/63] at ata0-master UDMA133 > acd0: DVDROM <COMPAQ DVD-ROM GDR8160B/0012> at ata0-slave PIO4 > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=4<ABORTED> > ata2-master: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=4<ABORTED> > ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH> > ata2-slave: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH> > ad4: FAILURE - SETFEATURES ENABLE RCACHE status=51<READY,DSC,ERROR> error=4<ABORTED> > ad4: FAILURE - SETFEATURES ENABLE WCACHE status=51<READY,DSC,ERROR> error=4<ABORTED> > ad4: 40MB <MiniScribe Corporation 8051A/3.73> [745/4/28] at ata2-master PIO0 > ad5: FAILURE - SETFEATURES ENABLE WCACHE status=51<READY,DSC,ERROR> error=5<ABORTED,ILLEGAL_LENGTH> > ad5: 41MB <Conner Peripherals 40MB - CP3041/S2.46> [1053/2/40] at ata2-slave PIO0 > ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ata3-master: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ata3-slave: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ad6: FAILURE - SETFEATURES ENABLE WCACHE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ad6: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-master PIO0 > ad7: FAILURE - SETFEATURES ENABLE WCACHE status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> > ad7: 102MB <st3120AT/REV184.0> [1024/12/17] at ata3-slave PIO0 > ad4: FAILURE - READ status=51<READY,DSC,ERROR> error=10<NID_NOT_FOUND> LBA=18 Mounting root from ufs:/dev/ad0s1a > > -- > No virus found in this outgoing message. > Checked by AVG Anti-Virus. > Version: 7.0.344 / Virus Database: 267.10.16/83 - Release Date: 8/26/2005 > > > _______________________________________________ > freebsd-hardware@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-hardware > To unsubscribe, send any mail to "freebsd-hardware-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050828110352.S43725>