Date: Sat, 29 Sep 2001 17:05:46 +0200 From: Arjan Knepper <arjan@jak.nl> To: Bruce@FreeBSD.ORG, Evans@FreeBSD.ORG Cc: freebsd-smp <freebsd-smp@freebsd.org> Subject: Re: Problems with accessing ports on multiple Cyclades YeP cards Message-ID: <3BB5E34A.40001@jak.nl> References: <20010928222423.J53717-100000@delplex.bde.org> <3BB487F5.3070602@jak.nl>
next in thread | previous in thread | raw e-mail | index | archive | help
This is a multi-part message in MIME format.
--------------030807050300010301050302
Content-Type: text/plain; charset=us-ascii; format=flowed
Content-Transfer-Encoding: 7bit
In the meanwhile I have updated the second machine to FreeBSD-4.4-STABLE
as well.
I have build two kernels both without support for the second serial port
(sio1) parallele port (ppc) and also have disabled those in the bios.
The system has 2 Cyclades YeP (PCI) boards and the kernel support both
device with device cy0 and device cy1. options CY_PCI_FASTINTR is ENABLED.
- Booting the SINGLE proc kernel locks-up just after the detection of
the first YeP (cy0) line:
cy0: <Cyclades Cyclom-Y Serial Adapter> port 0xec80-0xecff mem
0xfe104000-0xfe107fff,0xfe109400-0xfe10947f irq 11 at device 4.0 on pci0
- Booting the SINGLE proc kernel with the scsi-cable to the expansion
boards of the cy0 disconnected does NOT lock-up. The board-ports are
accessable through /dev/cuac00 to /dev/cuac0v eventhough the first board
(cy0) has no ports connected.
- The DUAL kernel boots without problems detects and connects both cy
adapters and ports. But when I try to access the first boards-ports
(cy0) with cu there is no response from the ports. Disconnecting the
ports works ok. The second board-ports are accessable and work ok.
When I connect a modem to one of the first board-ports and try to
conversate with the modem using cu -l /dev/cuac0f the DTR-light of the
modem lights up. I turns off as soon a I exit cu.
I have switched the pci-boards and expansion=boards but still got the
same results.
Does anyone have a clue or pointer?
TIA
Arjan Knepper
--------------030807050300010301050302
Content-Type: text/plain;
name="dmesg-v_dual.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="dmesg-v_dual.txt"
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-STABLE #2: Sat Sep 29 16:16:22 CEST 2001
arjan@fax2.teledirekt.nl:/usr/src/sys/compile/DELL_PE_2550
Calibrating clock(s) ... TSC clock: 930941130 Hz, i8254 clock: 1193161 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon/Celeron (930.96-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00352000 - 0x1ffe7fff, 533291008 bytes (130198 pages)
config> q
avail memory = 519098368 (506932K bytes)
Changing APIC ID for IO APIC #0 from 0 to 2 on chip
Changing APIC ID for IO APIC #1 from 0 to 3 on chip
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 16 pins in IOAPIC #1
SMP: CPU0 apic_initialize():
lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x000f0011, at 0xfec00000
io1 (APIC): apic id: 3, version: 0x000f0011, at 0xfec01000
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xc73e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
Other BIOS signatures found:
ACPI: 000fdc80
Preloaded elf kernel "kernel" at 0xc0328000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03280a8.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
SMP: CPU0 bsp_apic_configure():
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000270
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00081166)
Using $PIR table, 8 entries at 0xc00fc270
pcib-: pcib0 exists, using next available unit number
pcib-: pcib1 exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x1166, dev=0x0008, revid=0x23
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0008, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
IOAPIC #1 intpin 6 -> irq 2
Freeing (NOT implemented) redirected PCI irq 11.
found-> vendor=0x120e, dev=0x0101, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=2
map[10]: type 1, range 32, base fe109400, size 7
map[14]: type 1, range 32, base 0000ec80, size 7
map[18]: type 1, range 32, base fe104000, size 14
IOAPIC #1 intpin 2 -> irq 3
Freeing (NOT implemented) redirected PCI irq 10.
found-> vendor=0x120e, dev=0x0101, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=3
map[10]: type 1, range 32, base fe109000, size 7
map[14]: type 1, range 32, base 0000ec00, size 7
map[18]: type 1, range 32, base fe100000, size 14
found-> vendor=0x1002, dev=0x4752, revid=0x27
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 32, base 0000e800, size 8
map[18]: type 1, range 32, base fe108000, size 12
found-> vendor=0x1166, dev=0x0200, revid=0x50
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0211, revid=0x00
class=01-01-8a, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 000008b0, size 4
pci0: <PCI bus> on pcib0
cy0: <Cyclades Cyclom-Y Serial Adapter> port 0xec80-0xecff mem 0xfe104000-0xfe107fff,0xfe109400-0xfe10947f irq 2 at device 4.0 on pci0
cy0: driver is using old-style compatibility shims
cy1: <Cyclades Cyclom-Y Serial Adapter> port 0xec00-0xec7f mem 0xfe100000-0xfe103fff,0xfe109000-0xfe10907f irq 3 at device 8.0 on pci0
cy1: driver is using old-style compatibility shims
pci0: <ATI Mach64-GR graphics accelerator> (vendor=0x1002, dev=0x4752) at 14.0
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x8b0-0x8bf at device 15.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x08b0
ata0: mask=03 status0=50 status1=01
ata0: mask=03 ostat0=50 ostat2=01
ata0-master: ATAPI probe a=14 b=eb
ata0-slave: ATAPI probe a=14 b=eb
ata0: mask=03 status0=00 status1=01
ata0: devices=0c
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x08b8
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
pcib2: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x0962, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=3 secondarybus=3
IOAPIC #1 intpin 0 -> irq 5
Freeing (NOT implemented) redirected PCI irq 7.
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base feb00000, size 12
map[14]: type 1, range 32, base 0000ccc0, size 6
map[18]: type 1, range 32, base fe700000, size 20
pci2: <PCI bus> on pcib2
pcib4: <PCI to PCI bridge (vendor=8086 device=0962)> at device 2.0 on pci2
IOAPIC #1 intpin 15 -> irq 7
Freeing (NOT implemented) redirected PCI irq 5.
found-> vendor=0x9005, dev=0x00cf, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=7
map[10]: type 1, range 32, base 0000dc00, size 8
map[14]: type 1, range 64, base fe9ff000, size 12
IOAPIC #1 intpin 14 -> irq 10
Freeing (NOT implemented) redirected PCI irq 3.
found-> vendor=0x9005, dev=0x00cf, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[10]: type 1, range 32, base 0000d800, size 8
map[14]: type 1, range 64, base fe9fe000, size 12
pci3: <PCI bus> on pcib4
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xdc00-0xdcff mem 0xfe9ff000-0xfe9fffff irq 7 at device 4.0 on pci3
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 419 instructions downloaded
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd800-0xd8ff mem 0xfe9fe000-0xfe9fefff irq 10 at device 4.1 on pci3
ahc1: Reading SEEPROM...done.
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Secondary High byte termination Enabled
ahc1: Secondary Low byte termination Enabled
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xccc0-0xccff mem 0xfe700000-0xfe7fffff,0xfeb00000-0xfeb00fff irq 5 at device 4.0 on pci2
fxp0: using memory space register mapping
fxp0: Ethernet address 00:06:5b:04:5b:04
fxp0: PCI IDs: 8086 1229 1028 009b 0008
fxp0: Chip Type: 0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
pcib1: <ServerWorks host to PCI bridge> on motherboard
pci1: <PCI bus> on pcib1
pci-: pci3 exists, using next available unit number
pcib3: <ServerWorks host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib3
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff,0xec000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
isa_probe_children: probing PnP devices
SMP: enabled INTs: 1, 2, 3, 4, 5, 6, 7, 10, 14, apic_imen: 0x00ffbb01
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin 2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
bpf: ppp0 attached
new masks: bio 68004040, tty 6300001e, net 6700003e
bpf: sl0 attached
bpf: lo0 attached
SMP: AP CPU #1 Launched!
SMP: CPU1 apic_initialize():
lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
ata0-slave: ata_command: timeout waiting for intr
ata0-slave: identify failed
ata0-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata0-master: success setting PIO4 on generic chip
acd0: <LG DVD-ROM DRN-8080B/2.00> DVD-ROM drive at ata0 as master
acd0: 512KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Waiting 3 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:0:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 0 using 16bit transfers
ahc0: target 0 synchronous at 80.0MHz DT, offset = 0x3f
(ahc0:A:1:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:1:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 80.0MHz DT, offset = 0x3f
Creating DISK da0
Creating DISK da1
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
pass0: Serial Number 3JK0044500002204H28A
pass0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
pass1: Serial Number 3JK0013Y000072046K74
pass1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <DELL 1x4 U2W SCSI BP 1.30> Fixed Processor SCSI-2 device
pass2: Serial Number 1
pass2: 3.300MB/s transfers
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <DELL 1x4 U2W SCSI BP 1.30> Fixed Processor SCSI-2 device
pass2: Serial Number 1
pass2: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
da0: Serial Number 3JK0044500002204H28A
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17366MB (35566478 512 byte sectors: 255H 63S/T 2213C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
da1: Serial Number 3JK0013Y000072046K74
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17366MB (35566478 512 byte sectors: 255H 63S/T 2213C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 35551844, size 35551782 : OK
start_init: trying /sbin/init
da1s1: type 0xa5, start 63, end = 35551844, size 35551782 : OK
splash: image decoder found: green_saver
--------------030807050300010301050302
Content-Type: text/plain;
name="dmesg-v_single.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="dmesg-v_single.txt"
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-STABLE #1: Sat Sep 29 15:13:34 CEST 2001
apk@fax2.teledirekt.nl:/usr/src/sys/compile/DELL_PE_2550_SINGLE
Calibrating clock(s) ... TSC clock: 930940879 Hz, i8254 clock: 1193161 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 930962279 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (930.96-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009ffff, 651264 bytes (159 pages)
0x0033d000 - 0x1ffe7fff, 533377024 bytes (130219 pages)
config> q
avail memory = 519188480 (507020K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xc73e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4 Rev = 1.0
Other BIOS signatures found:
ACPI: 000fdc80
Preloaded elf kernel "kernel" at 0xc0316000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc03160a8.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000270
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00081166)
Using $PIR table, 8 entries at 0xc00fc270
pcib-: pcib0 exists, using next available unit number
pcib-: pcib1 exists, using next available unit number
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x1166, dev=0x0008, revid=0x23
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0008, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0006, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x120e, dev=0x0101, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base fe109400, size 7
map[14]: type 1, range 32, base 0000ec80, size 7
map[18]: type 1, range 32, base fe104000, size 14
found-> vendor=0x120e, dev=0x0101, revid=0x01
class=07-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base fe109000, size 7
map[14]: type 1, range 32, base 0000ec00, size 7
map[18]: type 1, range 32, base fe100000, size 14
found-> vendor=0x1002, dev=0x4752, revid=0x27
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 32, base 0000e800, size 8
map[18]: type 1, range 32, base fe108000, size 12
found-> vendor=0x1166, dev=0x0200, revid=0x50
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0211, revid=0x00
class=01-01-8a, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 000008b0, size 4
pci0: <PCI bus> on pcib0
cy0: <Cyclades Cyclom-Y Serial Adapter> port 0xec80-0xecff mem 0xfe104000-0xfe107fff,0xfe109400-0xfe10947f irq 11 at device 4.0 on pci0
cy0: no ports found!
cy0: driver is using old-style compatibility shims
cy1: <Cyclades Cyclom-Y Serial Adapter> port 0xec00-0xec7f mem 0xfe100000-0xfe103fff,0xfe109000-0xfe10907f irq 10 at device 8.0 on pci0
cy1: driver is using old-style compatibility shims
pci0: <ATI Mach64-GR graphics accelerator> (vendor=0x1002, dev=0x4752) at 14.0
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x8b0-0x8bf at device 15.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x08b0
ata0: mask=03 status0=50 status1=01
ata0: mask=03 ostat0=50 ostat2=01
ata0-master: ATAPI probe a=14 b=eb
ata0-slave: ATAPI probe a=14 b=eb
ata0: mask=03 status0=00 status1=01
ata0: devices=0c
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x08b8
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
pcib2: <ServerWorks host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x0962, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=3 secondarybus=3
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=7
map[10]: type 1, range 32, base feb00000, size 12
map[14]: type 1, range 32, base 0000ccc0, size 6
map[18]: type 1, range 32, base fe700000, size 20
pci2: <PCI bus> on pcib2
pcib4: <PCI to PCI bridge (vendor=8086 device=0962)> at device 2.0 on pci2
found-> vendor=0x9005, dev=0x00cf, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000dc00, size 8
map[14]: type 1, range 64, base fe9ff000, size 12
found-> vendor=0x9005, dev=0x00cf, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=3
map[10]: type 1, range 32, base 0000d800, size 8
map[14]: type 1, range 64, base fe9fe000, size 12
pci3: <PCI bus> on pcib4
ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xdc00-0xdcff mem 0xfe9ff000-0xfe9fffff irq 5 at device 4.0 on pci3
ahc0: Reading SEEPROM...done.
ahc0: Manual LVD Termination
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 419 instructions downloaded
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs
ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd800-0xd8ff mem 0xfe9fe000-0xfe9fefff irq 3 at device 4.1 on pci3
ahc1: Reading SEEPROM...done.
ahc1: Manual LVD Termination
ahc1: BIOS eeprom is present
ahc1: Secondary High byte termination Enabled
ahc1: Secondary Low byte termination Enabled
ahc1: Primary Low Byte termination Enabled
ahc1: Primary High Byte termination Enabled
ahc1: Downloading Sequencer Program... 419 instructions downloaded
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xccc0-0xccff mem 0xfe700000-0xfe7fffff,0xfeb00000-0xfeb00fff irq 7 at device 4.0 on pci2
fxp0: using memory space register mapping
fxp0: Ethernet address 00:06:5b:04:5b:04
fxp0: PCI IDs: 8086 1229 1028 009b 0008
fxp0: Chip Type: 0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
pcib1: <ServerWorks host to PCI bridge> on motherboard
pci1: <PCI bus> on pcib1
pci-: pci3 exists, using next available unit number
pcib3: <ServerWorks host to PCI bridge> on motherboard
pci4: <PCI bus> on pcib3
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff,0xec000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 684040, tty 630412, net 670492
bpf: sl0 attached
ata0-slave: ata_command: timeout waiting for intr
ata0-slave: identify failed
ata0-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata0-master: success setting PIO4 on generic chip
acd0: <LG DVD-ROM DRN-8080B/2.00> DVD-ROM drive at ata0 as master
acd0: 512KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Waiting 3 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:0:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:0:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 0 using 16bit transfers
ahc0: target 0 synchronous at 80.0MHz DT, offset = 0x3f
(ahc0:A:1:0): Sending PPR bus_width 1, period 9, offset 7f, ppr_options 2
(ahc0:A:1:0): Received PPR width 1, period 9, offset 3f,options 2
Filtered to width 1, period 9, offset 3f, options 2
ahc0: target 1 using 16bit transfers
ahc0: target 1 synchronous at 80.0MHz DT, offset = 0x3f
Creating DISK da0
Creating DISK da1
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
pass0: Serial Number 3JK0044500002204H28A
pass0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
pass1: Serial Number 3JK0013Y000072046K74
pass1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <DELL 1x4 U2W SCSI BP 1.30> Fixed Processor SCSI-2 device
pass2: Serial Number 1
pass2: 3.300MB/s transfers
pass2 at ahc0 bus 0 target 6 lun 0
pass2: <DELL 1x4 U2W SCSI BP 1.30> Fixed Processor SCSI-2 device
pass2: Serial Number 1
pass2: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
da0: Serial Number 3JK0044500002204H28A
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 17366MB (35566478 512 byte sectors: 255H 63S/T 2213C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST318305LC 2202> Fixed Direct Access SCSI-3 device
da1: Serial Number 3JK0013Y000072046K74
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da1: 17366MB (35566478 512 byte sectors: 255H 63S/T 2213C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 63, end = 35551844, size 35551782 : OK
start_init: trying /sbin/init
da1s1: type 0xa5, start 63, end = 35551844, size 35551782 : OK
splash: image decoder found: green_saver
--------------030807050300010301050302--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-smp" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3BB5E34A.40001>