Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 12 Sep 2017 11:57:40 +0300 (MSK)
From:      "Igor V. Ruzanov" <igorr@pochta.canmos.ru>
To:        Matthew Seaman <matthew@FreeBSD.org>
Cc:        freebsd-questions@freebsd.org
Subject:   Re: Need help
Message-ID:  <alpine.BSF.2.00.1709121149070.59850@pochta.canmos.ru>
In-Reply-To: <7f054774-5538-6884-fb5d-be155456d081@freebsd.org>
References:  <alpine.BSF.2.00.1709121013410.59850@pochta.canmos.ru> <7f054774-5538-6884-fb5d-be155456d081@freebsd.org>

Next in thread | Previous in thread | Raw E-Mail | Index | Archive | Help
On Tue, 12 Sep 2017, Matthew Seaman wrote:

|On 12/09/17 08:32, Igor V. Ruzanov wrote:
|> Hello, FreeBSD colleagues!
|> 
|> I have modern network card Intel i350T2V2 (peripheral dual gigabit port
|> NIC). And as far as i know all Intel cards should be normally detected
|> by the system. But with this NIC i have some troubles:
|> - the system sees the card as some ethernet device but cannot find
|> proper (igb) driver:
|> pcib6: <ACPI PCI-PCI bridge> irq 47 at device 3.2 on pci0
|> pci6: <ACPI PCI bus> on pcib6
|> pci6: <network, ethernet> at device 0.0 (no driver attached)
|> pci6: <network, ethernet> at device 0.1 (no driver attached)
|> - its from dmesg log.
|> 
|> Fnd `pciconf -lcvb' says:
|> none75@pci0:6:0:0:      class=0x020000 card=0x00008086 chip=0x151f8086
|> rev=0x01 hdr=0x00
|>     vendor     = 'Intel Corporation'
|>     class      = network
|>     subclass   = ethernet
|>     bar   [10] = type Memory, range 32, base 0x91920000, size 131072,
|> enabled
|>     bar   [18] = type I/O Port, range 32, base 0x2020, size 32, enabled
|>     bar   [1c] = type Memory, range 32, base 0x919c4000, size 16384,
|> enabled
|>     cap 01[40] = powerspec 3  supports D0 D3  current D0
|>     cap 05[50] = MSI supports 1 message, 64 bit, vector masks
|>     cap 11[70] = MSI-X supports 10 messages
|>                  Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
|>     cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS link
|> x4(x4)
|>                  speed 5.0(5.0) ASPM disabled(L0s/L1)
|>     ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
|>     ecap 000e[150] = ARI 1
|>     ecap 0010[160] = SRIOV 1
|>     ecap 0017[1a0] = TPH Requester 1
|>     ecap 0018[1c0] = LTR 1
|>     ecap 000d[1d0] = ACS 1
|> none76@pci0:6:0:1:      class=0x020000 card=0x00008086 chip=0x151f8086
|> rev=0x01 hdr=0x00
|>     vendor     = 'Intel Corporation'
|>     class      = network
|>     subclass   = ethernet
|>     bar   [10] = type Memory, range 32, base 0x91900000, size 131072,
|> enabled
|>     bar   [18] = type I/O Port, range 32, base 0x2000, size 32, enabled
|>     bar   [1c] = type Memory, range 32, base 0x919c0000, size 16384,
|> enabled
|>     cap 01[40] = powerspec 3  supports D0 D3  current D0
|>     cap 05[50] = MSI supports 1 message, 64 bit, vector masks
|>     cap 11[70] = MSI-X supports 10 messages
|>                  Table in map 0x1c[0x0], PBA in map 0x1c[0x2000]
|>     cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS link
|> x4(x4)
|>                  speed 5.0(5.0) ASPM disabled(L0s/L1)
|>     ecap 0001[100] = AER 2 0 fatal 0 non-fatal 1 corrected
|>     ecap 000e[150] = ARI 1
|>     ecap 0010[160] = SRIOV 1
|>     ecap 0017[1a0] = TPH Requester 1
|>     ecap 000d[1d0] = ACS 1
|> 
|> My server is:
|> - system is FreeBSD-10.3-RELEASE-p20
|> - motherboard: Intel S2600WT (dual CPU socket board)
|> - one CPU installed
|> 
|> Maybe someone has experience with this inetl NIC? As seen from pciconf
|> output the NIC has a set of VFs (Virtual Functions) needed in
|> virtualization environments. And chip id is 0x151F8086 - the id that
|> igb-driver does not know about. Maybe i need some preconfiguration of
|> this card? Or this device is not compatible with non-virtualization
|> systems like usual physical server?
|> 
|> Big thanks in advance!
|
|Pretty much all Intel NICs should be supported.  i350 certainly should
|use the igb(4) driver.
|
Totally agree!


|Can you try booting a more recent version of FreeBSD from a memstick
|image and see if the NIC is properly detected there?  If that works,
|then upgrading should solve your problems.  (11.1 probably your best
|bet, but there's also 10.4 in the late stages of the release process.)
|
|Beyond that I suggest taking your question to the freebsd-net@ list as
|you're likely to come to the attention of the people who write the
|drivers there.
|
I tried :) FreeBSD-11.x (not sure that it was 11.1, but it does not 
matter). Also with Linux RHEL7 (with kernel 3.10) in rescue console (but i 
was able to load igb-, kvm-modules) i could see exactly the same symptoms.
Anyway thank your for your reply and suggestion, Matthew! I'll try to ask 
my question to the freebsd-net group.



Want to link to this message? Use this URL: <http://docs.FreeBSD.org/cgi/mid.cgi?alpine.BSF.2.00.1709121149070.59850>