Date: Tue, 17 Nov 1998 15:04:19 -0700 From: Wes Peters <wpeters@xylan.com> To: questions@FreeBSD.ORG Subject: fxp0 vs. 3.0 -- more info Message-ID: <3651F2E3.5F72A826@xylan.com>
next in thread | raw e-mail | index | archive | help
First, I should point out this machine HAD BEEN RUNNING 2.2.6-RELEASE just fine, right up until I lobotomized^H^H^H^H^H^Hupgraded it to 3.0. I booted single-user and commented out the fxp configuration so I could do a little more testing. Here's what dmesg turns up: Probing for devices on PCI bus 0: chip0: <Host to PCI bridge (vendor=8086 device=7180) rev 0x03 on pci0.0.0 chip1: <PCI to PCI bridge (vendor=8086 device=7181) rev 0x03 on pci0.1.0 chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0 ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 chip3: <Intel 82371AB USB host controller> rev 0x01 int d ireq 9 on pci0.7.2 chip4: <Intel 82371AB Power management controller> rev 0x01 on pci0.7.3 fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 10 on pci0.16.0 fxp0: Ethernet address 00:00:39:09:70:0c Probing for devices on PCI bus 1: vga0: <ATI model 4742 graphics accelerator> rev 0x5c on pci1.0.0 Probing for devices on the ISA bus: sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA color <16 virtual consoles, flags=0x0> sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A lpt0 not found psm0 at 0x60-0x64 irq 12 on motherboard pms0: model Generic PS/2 mouse, device ID 0 fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold wdc0 at 0x1f0-0x1f7 irq 14 on isa wdc0: unit 0 (wd0): <WDC AC24300L> wd0: 4112MB (8421840 sectors), 8912 cyls, 15 heads, 63 S/T, 512 B/S wdc1 at 0x170-0x177 irq 15 on isa wdc1: unti 0 (atapi): <TOSHIBA CD-ROM XM-6202B/1110>, removable, accel, ovlap, dma, iordis wcd0: 5512Kb/sec, 256Kb cache, audio play, 255 volume levels, ejectable tray wcd0: no disc inside, unlocked npx0 on motherboard npx0: INT 16 interface changing root device to wd0s2a If I try to configure fxp0, the system hangs immediately, before the console can even move the cursor to the next line on the screen following the ifconfig command. The command I used is: ifconfig fxp0 inet 192.168.110.151 and the system just hangs hard. Help!?!?!?!? -- Wes Peters Who's going to save you Principal Engineer When you're a slave to Xylan Corporation A diamond as big as the Ritz wpeters@xylan.com -- Jimmy Buffett To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3651F2E3.5F72A826>