Date: Sun, 10 Oct 1999 13:48:57 -0400 (EDT) From: Kenneth Culver <culverk@culverk.student.umd.edu> To: Soren Schmidt <sos@freebsd.dk> Cc: freebsd-current@FreeBSD.ORG Subject: Re: ATA driver Message-ID: <Pine.BSF.4.10.9910101346180.302-100000@culverk.student.umd.edu> In-Reply-To: <Pine.BSF.4.10.9910101334220.3885-100000@culverk.student.umd.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
It doesn't seem to have bad sectors... found-> vendor=0x109e, dev=0x036e, revid=0x02 class=04-00-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 intpin=a, irq=9 map[0]: type 3, range 32, base ea002000, size 12 found-> vendor=0x109e, dev=0x0878, revid=0x02 class=04-80-00, hdrtype=0x00, mfdev=1 subordinatebus=0 secondarybus=0 intpin=a, irq=9 map[0]: type 3, range 32, base ea000000, size 12 found-> vendor=0x1011, dev=0x0009, revid=0x22 class=02-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=10 map[0]: type 4, range 32, base 0000e400, size 7 map[1]: type 1, range 32, base ea001000, size 7 pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 found-> vendor=0x8086, dev=0x7800, revid=0x21 class=03-00-00, hdrtype=0x00, mfdev=0 subordinatebus=0 secondarybus=0 intpin=a, irq=255 map[0]: type 3, range 32, base e6000000, size 24 map[1]: type 1, range 32, base e5000000, size 19 pci1: <PCI bus> on pcib1 vga-pci0: <VGA-compatible display device> at device 0.0 on pci1 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 ata-pci0: <Intel PIIX4 IDE controller> at device 7.1 on pci0 ata-pci0: Busmastering DMA supported ata0: iobase=0x01f0 altiobase=0x03f6 ata0: mask=03 status0=50 status1=50 ata0: mask=03 status0=50 status1=50 ata0: devices = 0x3 ata0 at 0x01f0 irq 14 on ata-pci0 ata1: iobase=0x0170 altiobase=0x0376 ata1: mask=03 status0=50 status1=10 ata1: mask=03 status0=50 status1=10 ata1: devices = 0x9 ata1 at 0x0170 irq 15 on ata-pci0 chip1: <UHCI USB controller> irq 11 at device 7.2 on pci0 intpm0: <Intel 82371AB Power management controller> at device 7.3 on pci0 intpm0: I/O mapped 5000 intpm0: intr IRQ 9 enabled revision 0 smbus0: <System Management Bus> on intsmb0 smb0: <SMBus general purpose I/O> on smbus0 intpm0: PM I/O mapped 4000 pci0: unknown card (vendor=0x121a, dev=0x0002) at 13.0 pci0: unknown card (vendor=0x121a, dev=0x0002) at 15.0 bktr0: <BrookTree 878> irq 9 at device 17.0 on pci0 using shared irq9. brooktree0: PCI bus latency is 64. bktr0: buffer size 3555328, addr 0x5000000 bktr: GPIO is 0x00fffffb subsytem 0x0070 0x13eb bktr0: Hauppauge Model 61291 D110 Hauppauge WinCast/TV, Philips NTSC tuner, remote control. pci0: unknown card (vendor=0x109e, dev=0x0878) at 17.1 irq 9 de0: <Digital 21140A Fast Ethernet> irq 10 at device 19.0 on pci0 de0: 21140A [10-100Mb/s] pass 2.2 de0: address 00:c0:f0:1f:21:02 bpf: de0 attached fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 psm0: current command byte:0047 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 00 00 64 psm: status 00 03 64 psm: status 00 03 64 psm: status 10 00 64 psm: data 08 00 00 psm: data 08 00 00 psm: status 00 02 64 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000000, packet size:4 psm0: syncmask:c8, syncbits:08 vga0: <Generic ISA VGA> at port 0x3b0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3b0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k vga0: vga: WARNING: video mode switching is not fully supported on this adapter VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 28 0b 10 ff ff 09 0f 00 0e eb 2d 27 28 90 2b 91 bf 1f c0 9c 0e 8f 28 96 b9 01 01 01 01 00 28 0e 10 ff ff 09 0f 00 0e eb 31 27 28 92 2c 90 05 3e c0 e9 0c df 28 e9 fc 02 01 01 01 00 32 11 10 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> sc0: fb0 kbd0 sio0: irq maps: 0x41 0x51 0x41 0x41 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: irq maps: 0x41 0x49 0x41 0x41 sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc: parallel port found at 0x378 ppc: chipset forced to generic ppc0: EPP SPP ppc0 at port 0x378-0x37f irq 7 flags 0x40 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip: irq 7 plip0: <PLIP network interface> on ppbus 0 bpf: lp0 attached lpt0: <generic printer> on ppbus 0 lpt0: Interrupt-driven port ppi0: <generic parallel i/o> on ppbus 0 vpo0: <Iomega VPI0 Parallel to SCSI interface> on ppbus 0 vpo0: EPP 1.9 mode sb0 at port 0x220 irq 5 drq 1 on isa0 snd0: <SoundBlaster 16 4.16> isa_compat: didn't get drq for sbxvi sbxvi0 at port 0xffffffff drq 1 on isa0 isa_compat: didn't get ports for sbxvi isa_compat: didn't get drq for sbxvi snd0: <SoundBlaster 16 4.16> WARNING: "snd" is usurping "snd"'s cdevsw[] sbmidi0 at port 0x330 on isa0 snd0: <SoundBlaster MPU-401> WARNING: "snd" is usurping "snd"'s cdevsw[] opl0 at port 0x388 on isa0 snd0: <Yamaha OPL3 FM> WARNING: "snd" is usurping "snd"'s cdevsw[] BIOS Geometries: 0:03ff0f3f 0..1023=1024 cylinders, 0..15=16 heads, 1..63=63 sectors 1:03ff0e3f 0..1023=1024 cylinders, 0..14=15 heads, 1..63=63 sectors 2:03ff0e3f 0..1023=1024 cylinders, 0..14=15 heads, 1..63=63 sectors 0 accounted for Device configuration finished. bpf: lo0 attached bpf: ppp0 attached new masks: bio 4008c040, tty 4003109a, net 4007169a ata0: master: success setting up UDMA2 mode on PIIX4 chip ad0: piomode=4 dmamode=2 udmamode=2 ad0: <Maxtor 90845D4/GAS54112> ATA-4 disk at ata0 as master ad0: 8063MB (16514064 sectors), 16383 cyls, 16 heads, 63 S/T, 512 B/S ad0: 16 secs/int, 0 depth queue, UDMA33 Creating DISK ad0 Creating DISK wd0 ata0: slave: success setting up UDMA2 mode on PIIX4 chip ad1: piomode=4 dmamode=2 udmamode=2 ad1: <Maxtor 84320D4/NAVX1920> ATA-3 disk at ata0 as slave ad1: 4120MB (8438850 sectors), 8930 cyls, 15 heads, 63 S/T, 512 B/S ad1: 16 secs/int, 0 depth queue, UDMA33 Creating DISK ad1 Creating DISK wd1 ata1: master: success setting up UDMA2 mode on PIIX4 chip ad2: piomode=4 dmamode=2 udmamode=2 ad2: <FUJITSU MPC3064AT/6020> ATA-3 disk at ata1 as master ad2: 6187MB (12672450 sectors), 13410 cyls, 15 heads, 63 S/T, 512 B/S ad2: 16 secs/int, 0 depth queue, UDMA33 Creating DISK ad2 Creating DISK wd2 ata1-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1 atapi: MODE_SENSE_BIG - UNIT ATTENTION skey=6 asc=29 ascq=00 error=00 acd0: <CD-ROM 40X/AKU/U30> CDROM drive at ata1 as slave , 128KB buffer, PIO acd0: supported read types: CD-DA acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray acd0: Medium: CD-ROM 120mm data/audio disc loaded, unlocked (probe6:vpo0:0:6:0): INQUIRY. CDB: 12 1 80 0 ff 0 (probe6:vpo0:0:6:0): ILLEGAL REQUEST asc:24,0 (probe6:vpo0:0:6:0): Invalid field in CDB Creating DISK da0 (da0:vpo0:0:6:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 (da0:vpo0:0:6:0): NOT READY asc:3a,0 (da0:vpo0:0:6:0): Medium not present da0 at vpo0 bus 0 target 6 lun 0 da0: <IOMEGA ZIP 100 D.09> Removable Direct Access SCSI-2 device da0: Attempt to query device size failed: NOT READY, Medium not present Considering FFS root f/s. changing root device to wd1s1a wd1s1: type 0xa5, start 63, end = 8438849, size 8438787 : OK start_init: trying /sbin/init de0: enabling 10baseT port wd2s1: type 0xa5, start 63, end = 12672449, size 12672387 : OK wd0s1: type 0xc, start 63, end = 16514063, size 16514001 : OK Linux-ELF exec handler installed splash: image decoder found: green_saver To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.9910101346180.302-100000>