Date: Tue, 22 Apr 1997 07:02:07 +0100 From: "Ian Vaudrey" <i.vaudrey@test.nemko.ltd.uk> To: "freebsd-questions" <freebsd-questions@freebsd.org> Subject: Re: ../../sys/cdefs.h: Bad address Message-ID: <199704220602.HAA01407@mail.nemko.ltd.uk>
next in thread | raw e-mail | index | archive | help
I should've mentioned that this is on 2.2.1-RELEASE. Also, I've attached my kernel config file - as I said, this is just the GENERIC file with the devices I don't need commented out. The box spec is 486DX2/80, Adaptec 1542 with 1 hard drive and 1 CDROM, 3Com 3C509 NIC. - Ian # # GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks # # For more information read the handbook part System Administration -> # Configuring the FreeBSD Kernel -> The Configuration File. # The handbook is available in /usr/share/doc/handbook or online as # latest version from the FreeBSD World Wide Web server # <URL:http://www.FreeBSD.ORG/>; # # An exhaustive list of options and more detailed explanations of the # device lines is present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $Id: GENERIC,v 1.77.2.4 1997/02/22 20:31:24 joerg Exp $ machine "i386" #cpu "I386_CPU" cpu "I486_CPU" #cpu "I586_CPU" #cpu "I686_CPU" ident MAIL maxusers 10 #option MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem #options NFS #Network Filesystem #options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=7 #Be pessimistic about Joe SCSI device options BOUNCE_BUFFERS #include support for DMA bounce buffers options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on wd0 controller isa0 #controller eisa0 #controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 disk fd1 at fdc0 drive 1 tape ft0 at fdc0 drive 2 #controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr #disk wd0 at wdc0 drive 0 #disk wd1 at wdc0 drive 1 #controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr #disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 #options ATAPI #Enable ATAPI support for IDE bus #options ATAPI_STATIC #Don't do it as an LKM #device wcd0 #IDE CD-ROM # A single entry for any of these controllers (ncr, ahb, ahc, amd) is # sufficient for any number of installed devices. #controller ncr0 #controller amd0 #controller ahb0 #controller ahc0 #controller bt0 at isa? port "IO_BT0" bio irq ? vector bt_isa_intr #controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr controller aha0 at isa? port "IO_AHA0" bio irq ? drq 6 vector ahaintr #controller aic0 at isa? port 0x340 bio irq 11 vector aicintr #controller nca0 at isa? port 0x1f88 bio irq 10 vector ncaintr #controller nca1 at isa? port 0x350 bio irq 5 vector ncaintr #controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr controller scbus0 device sd0 device od0 #See LINT for possible `od' options. device st0 device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr #device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr #controller matcd0 at isa? port 0x230 bio #device scd0 at isa? port 0x230 bio # syscons is the default console driver, resembling an SCO console device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint #options PCVT_FREEBSD=210 # pcvt running on FreeBSD >= 2.0.5 #options XSERVER # include code for XFree86 #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Mandatory, don't remove device npx0 at isa? port "IO_NPX" irq 13 vector npxintr # # Laptop support (see LINT for more options) # device apm0 at isa? disable # Advanced Power Management options APM_BROKEN_STATCLOCK # Workaround some buggy APM BIOS # PCCARD (PCMCIA) support #controller crd0 #device pcic0 at crd? #device pcic1 at crd? device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr device sio2 at isa? disable port "IO_COM3" tty irq 5 vector siointr device sio3 at isa? disable port "IO_COM4" tty irq 9 vector siointr device lpt0 at isa? port? tty irq 7 vector lptintr device lpt1 at isa? port? tty device mse0 at isa? port 0x23c tty irq 5 vector mseintr #device psm0 at isa? disable port "IO_KBD" conflicts tty irq 12 vector psmintr # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. #device de0 #device fxp0 #device vx0 #device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 vector edintr #device ed1 at isa? port 0x300 net irq 5 iomem 0xd8000 vector edintr #device ie0 at isa? port 0x360 net irq 7 iomem 0xd0000 vector ieintr device ep0 at isa? port 0x300 net irq 10 vector epintr #device ex0 at isa? port 0x300 net irq 10 iomem 0xd0000 vector exintr #device fe0 at isa? port 0x300 net irq ? vector feintr #device ix0 at isa? port 0x300 net irq 10 iomem 0xd0000 iosiz 32768 vector ixintr #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr #device lnc0 at isa? port 0x280 net irq 10 drq 0 vector lncintr #device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr #device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr pseudo-device loop pseudo-device ether pseudo-device log pseudo-device sl 1 # ijppp uses tun instead of ppp device #pseudo-device ppp 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing ---------- > From: Ian Vaudrey <i.vaudrey@test.nemko.ltd.uk> > To: freebsd-questions <freebsd-questions@freebsd.org> > Subject: cpp: ../../sys/cdefs.h: Bad address > Date: 21 April 1997 21:18 > > Hello, > > I've just tried to compile a custom kernel following the instructions > given in the handbook. Everything up to and including the 'make depend' > step completed with no errors, but the next step - 'make' - terminates > with the following text: > > cc -c -O -Wreturn-type -Wcomment -Wredundant-decls > -Wimplicit -Wnested-externs -Wstrict-prototypes > -Wmissing-prototypes -Wpointer-arith -nostdinc -I- > -I. -I. ./.. -I/usr/include -DAPM_BROKEN_STATCLOCK > -DFAILSAFE -DCOMPAT_43 -DCD9660 -DFFS -DINET -DKERNEL > ../../kern/kern_descrip.c > cpp: ../../sys/cdefs.h: Bad address > *** Error code 1 > > Stop. > > The custom kernel is simply the GENERIC file with all devices that do > not exist on my system commented out. > > Any ideas on what the problem could be? > > - Ian >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199704220602.HAA01407>