Date: Thu, 6 Jan 2005 23:30:34 +0100 From: "Jorn Argelo" <jorn@wcborstel.nl> To: Tom Vilot <tom@vilot.com>, FreeBSD Questions <questions@freebsd.org> Subject: Re: SCSI Hardware problem? Message-ID: <20050106222541.M42982@wcborstel.nl> In-Reply-To: <41DDB91C.5000600@vilot.com> References: <41DDB91C.5000600@vilot.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 06 Jan 2005 15:18:04 -0700, Tom Vilot wrote > This looks to me like I've got a hardware problem. SCSI drive 0:4:0 - > - or is this perhaps something else? > > I had to manually type this in ... :) copying it off the screen > since I don't see this stuff in a log anywhere. > > FreeBSD 5.3 on a dual 450MHz Xeon with SCSI and IDE. GENERIC kernel. > > There was stuff above this, but it had scrolled off the screen and > the console was locked up. > > da1 (scsi 4 on bus 0) is my boot drive. > > ----------------------------------- > > <<<<<<<<<<<<<<<<<<<<Dump Card State Ends>>>>>>>>>>>>>>>>>>>> > > (da1:ahc1:0:4:0): SCB 0x3 - timed out > > sg[0] - Addr 0x2574b000 > > (da1:ahc1:0:4:0): Queuing a BDR SCB > (da1:ahc1:0:4:0): no longer in timeout, status = 24a > ahc1: Timedout SCBs already complete. Interrupts may not be functioning. > (da1:ahc1:0:4:0): WRITE(10). CDB: 2a, 0 0 47 49 23 0 0 4 0 > (da1:ahc1:0:4:0): CAM Status: SCSI Status Error > (da1:ahc1:0:4:0): SCSI Status: Check Condition > (da1:ahc1:0:4:0): UNIT ATTENTION asc:29,1 > (da1:ahc1:0:4:0): Power on occurred > (da1:ahc1:0:4:0): Retrying Command (per sense Data) > (da1:ahc1:0:4:0): WRITE(10). CDB: 2a, 0 0 47 49 23 0 0 4 0 > (da1:ahc1:0:4:0): CAM Status: SCSI Status Error > (da1:ahc1:0:4:0): CAM Status: Check Condition > (da1:ahc1:0:4:0): UNIT ATTENTION asc:29,1 > (da1:ahc1:0:4:0): Power on occurred > (da1:ahc1:0:4:0): Retries Exhausted > (da1:ahc1:0:4:0): lost device > (da1:ahc1:0:4:0): invalidating pack > panic: initiate_write_inodeblock_ufs2: already started > Uptime: 3d12h50m3s Make sure your SCSI controller is supported by the driver you're using. If it is, it's probably a faulty disk. > > ----------------------------------- > > I'm guessing I will want to copy this entire drive over to another > one. What's the best way .... dd? Doesn't matter too much AFAIK. As long as you can access the disk properly. > > Oh, one other question ... > > I'm used to runlevels on Linux. When I reset this machine, I'm > presented with the prompt asking me for the default shell (/bin/sh). > I hit enter, and I'm in sh where I can fsck the other drives and > mount them. Cool. But ....once I have done that, how do I tell BSD > to basically "continue" where it left off (i.e. run /etc/netstart > sshd, httpd, psqld, zope, etc) without manually invoking each of > those items? I assume you boot in single user mode. I would just reboot the machine again and boot normally (multi-user mode) after you're finished with fsck and stuff. Cheers, Jorn > Thanks in advance. > > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050106222541.M42982>