Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 29 Jun 2005 16:42:49 +0100
From:      Dominic Marks <dom@goodforbusiness.co.uk>
To:        freebsd-stable@freebsd.org
Cc:        pjd@freebsd.org
Subject:   graid3 + rsync + 5.4-STABLE repeatable panic (Fatal trap 12: page fault while in kernel mode)
Message-ID:  <200506291642.50119.dom@goodforbusiness.co.uk>

next in thread | raw e-mail | index | archive | help
Hello,

I'm trying to use graid3 to create a raid volume from three
250GB SATA discs. I can successfully label, format, and mount
the disc. The problem arises when I try and migrate some data
on to the new volume. I'm using rsync to do this from over the
local network, unfortunately this seems to be produce an
immediate and reproduceable panic (hand copied):

Fatal trap 12: page fault while in kernel mode

fault virtual address = 0xc30f8000
fault code = supervisor write, page not present
instruction pointer = 0x8:0xc05e9783
stack pointer = 0x10:0xd8030c38
frame pointer = 0x10:0xd8030c80
code segment = base 0x0, limit 0xfffff type 0x1b
             = DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 617 (g_raid3 raid)
trap number = 12
panic: page fault

Other programs (touch, ls, diskinfo, etc) do not seem to provoke
the panic, but rsync will kill the system within a second.

I got a dump (once), but I think it is corrupt in some way
because I have not been able to get a backtrace or any other
useful data from it.

# kgdb kernel.debug /usr/crash/vmcore.0
kgdb: kvm_read: invalid address (f9)

(This line is printed again, and again, and again ...)

This may be because I compiled my debugging kernel after I had
installed the system, although it should have been an identical
source tree ... I'm currently rebuilding the system to
the freshest available -STABLE in the hope that may give a
full backtrace.

FreeBSD mrt.helenmarks.co.uk 5.4-STABLE FreeBSD 5.4-STABLE #0
Mon Jun 27 09:34:02 BST 2005
root@mrt.helenmarks.co.uk:/usr/obj/usr/src/sys/DEV i386

The only thing slightly odd about the machine is that each
disc is one its own SATA controller. One disc is attached to an
Intel ICH6 the other two are attached two Silicon Image (3112)
based cards. The root device is ad2, since the additional cards
have pushed themselves to the front. This is a temporary setup
to facilitate migration of data from system to system.

If I can do anything to help track the problem down, please say.
I really want this to work, and I have some time in which to run
tests.

* A side note, I have noticed that the panic is often accompanied by
a ATA DMA timeout (ad1). Could this cause the panic to occur?

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.4-STABLE #0: Mon Jun 27 09:34:02 BST 2005
    root@mrt.helenmarks.co.uk:/usr/obj/usr/src/sys/DEV
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
ACPI APIC Table: <DELL   PESC420>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU 2.53GHz (2527.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf41  Stepping = 1
  
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  = 526958592 (502 MB)
avail memory = 509628416 (486 MB)
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL PESC420> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci0: <display, VGA> at device 2.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5751 Gigabit Ethernet, ASIC rev. 0x4001> mem 
0xdfdf0000-0xdfdfffff irq 16 at device 0.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 
1000baseTX-FDX, auto
bge0: Ethernet address: 00:11:11:c3:2c:91
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci3: <ACPI PCI bus> on pcib3
pci0: <serial bus, USB> at device 29.0 (no driver attached)
pci0: <serial bus, USB> at device 29.1 (no driver attached)
pci0: <serial bus, USB> at device 29.2 (no driver attached)
pci0: <serial bus, USB> at device 29.3 (no driver attached)
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci4: <ACPI PCI bus> on pcib4
atapci0: <SiI 3112 SATA150 controller> port 
0xdce0-0xdcef,0xdcb4-0xdcb7,0xdcc8-0xdccf,0xdcb0-0xdcb3,0xdcc0-0xdcc7 
mem 0xdfaffc00-0xdfaffdff irq 17 at device 1.0 on pci4
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
atapci1: <SiI 3112 SATA150 controller> port 
0xdcf0-0xdcff,0xdcbc-0xdcbf,0xdcd8-0xdcdf,0xdcb8-0xdcbb,0xdcd0-0xdcd7 
mem 0xdfaffe00-0xdfafffff irq 18 at device 2.0 on pci4
ata4: channel #0 on atapci1
ata5: channel #1 on atapci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci2: <Intel ICH6 UDMA100 controller> port 
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 16 at device 31.1 
on pci0
ata0: channel #0 on atapci2
ata1: channel #1 on atapci2
atapci3: <Intel ICH6 SATA150 controller> port 
0xfea0-0xfeaf,0xfe30-0xfe33,0xfe20-0xfe27,0xfe10-0xfe13,0xfe00-0xfe07 
irq 20 at device 31.2 on pci0
ata6: channel #0 on atapci3
ata7: channel #1 on atapci3
ichsmb0: <SMBus controller> port 0xece0-0xecff irq 17 at device 31.3 on 
pci0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on 
acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 
0xcf800-0xcffff,0xce000-0xcf7ff,0xc9800-0xcdfff,0xc0000-0xc97ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on 
isa0
ppc0: parallel port not found.
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounter "TSC" frequency 2527010839 Hz quality 800
Timecounters tick every 1.250 msec
IPsec: Initialized Security Association Processing.
ad0: 238475MB <WDC WD2500JD-22HBB0/08.02D08> [484521/16/63] at 
ata4-master SATA150
ad1: 238475MB <WDC WD2500JD-22HBB0/08.02D08> [484521/16/63] at 
ata5-master SATA150
ad2: 76319MB <WDC WD800JD-60JRA0/05.01C05> [155061/16/63] at ata6-master 
SATA150
ad3: 238475MB <WDC WD2500JD-00HBB0/08.02D08> [484521/16/63] at 
ata7-master SATA150
Mounting root from ufs:/dev/ad2s1a
WARNING: / was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted

Thanks very much,
-- 
Dominic
GoodforBusiness.co.uk
I.T. Services for SMEs in the UK.



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200506291642.50119.dom>