Date: Wed, 23 Nov 2005 14:04:36 +0100 (CET) From: kama <kama@pvp.se> To: freebsd-stable@freebsd.org Subject: 6.0 Stable reboots randomly during high load. Message-ID: <20051123134710.G57888@ns1.as.pvp.se>
next in thread | raw e-mail | index | archive | help
I have a HP DL380G3 Dual 2.4 w HT disabled.
This server is running as a newsserver (Diablo) and recieving more or less
a full feed. aprox 200Mbps in and out. When the load rises the system
reboots.
I can occupy it with high CPU load w/o problem, but once I allow
connections to the machine, it will operate for a couple of hours and then
reboot. It gets aprox 100 connections to the machine, all of them either
write or read from disk.
The kernel is GENERIC with small changes. (look at diff below)
This system had a working 5.4 system installed before, that did not suffer
from these reboots.
How do I proceed for further gathering of information before I downgrade
it to 5.4 again?
/Bjorn
- snip -
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-STABLE #8: Mon Nov 21 14:45:30 CET 2005
root@newspeer3:/usr/obj/usr/src/sys/newspeer
ACPI APIC Table: <COMPAQ 00000083>
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2387.52-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4400<CNTX-ID,<b14>>
Hyperthreading: 2 logical CPUs
real memory = 4110393344 (3919 MB)
avail memory = 4022607872 (3836 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 6
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-15 on motherboard
ioapic1 <Version 1.1> irqs 16-31 on motherboard
ioapic2 <Version 1.1> irqs 32-47 on motherboard
ioapic3 <Version 1.1> irqs 48-63 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <COMPAQ P29> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link IUSB> on acpi0
pci_link1: <ACPI PCI Link IN16> on acpi0
pci_link2: <ACPI PCI Link IN17> on acpi0
pci_link3: <ACPI PCI Link IN18> on acpi0
pci_link4: <ACPI PCI Link IN19> on acpi0
pci_link5: <ACPI PCI Link IN20> on acpi0
pci_link6: <ACPI PCI Link IN21> on acpi0
pci_link7: <ACPI PCI Link IN22> on acpi0
pci_link8: <ACPI PCI Link IN23> on acpi0
pci_link9: <ACPI PCI Link IN24> on acpi0
pci_link10: <ACPI PCI Link IN25> on acpi0
pci_link11: <ACPI PCI Link IN26> on acpi0
pci_link12: <ACPI PCI Link IN27> on acpi0
pci_link13: <ACPI PCI Link IN28> on acpi0
pci_link14: <ACPI PCI Link IN29> on acpi0
pci_link15: <ACPI PCI Link IN30> on acpi0
pci_link16: <ACPI PCI Link IN31> on acpi0
pci_link17: <ACPI PCI Link IN32> on acpi0
pci_link18: <ACPI PCI Link IN33> on acpi0
pci_link19: <ACPI PCI Link IN34> on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x920-0x923 on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 3.0 (no driver attached)
pci0: <base peripheral> at device 4.0 (no driver attached)
pci0: <base peripheral> at device 4.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 15.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xf5ef0000-0xf5ef0fff irq 7 at
device 15.2 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib1: <ACPI Host-PCI bridge> on acpi0
pci1: <ACPI PCI bus> on pcib1
ciss0: <Compaq Smart Array 5i> port 0x3000-0x30ff mem
0xf7cc0000-0xf7cfffff,0xf7bf0000-0xf7bf3fff irq 30 at device 3.0 on pci1
ciss0: [GIANT-LOCKED]
pcib2: <ACPI Host-PCI bridge> on acpi0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xf7df0000-0xf7dfffff irq 29 at device 1.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:0b:cd:f3:af:4d
bge1: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xf7de0000-0xf7deffff irq 31 at device 2.0 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: Ethernet address: 00:0b:cd:f3:af:4c
pcib3: <ACPI Host-PCI bridge> on acpi0
pci3: <ACPI PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 1.0 on pci3
pci4: <PCI bus> on pcib4
ciss1: <HP Smart Array 6400> port 0x4000-0x40ff mem 0xf7ef0000-0xf7ef1fff
irq 20 at device 4.0 on pci4
ciss1: [GIANT-LOCKED]
ciss2: <HP Smart Array 6400 EM> port 0x4400-0x44ff mem
0xf7e70000-0xf7e71fff irq 21 at device 5.0 on pci4
ciss2: [GIANT-LOCKED]
pcib5: <ACPI Host-PCI bridge> on acpi0
pci6: <ACPI PCI bus> on pcib5
pci6: <base peripheral, PCI hot-plug controller> at device 30.0 (no driver
attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on
acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcffff,0xd0000-0xd17ff,0xee000-0xeffff
on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
acd0: CDROM <COMPAQ CD-ROM SN-124/N104> at ata0-master PIO4
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 17359MB (35553120 512 byte sectors: 255H 32S/T 4357C)
da1 at ciss0 bus 0 target 1 lun 0
da1: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da1: 135.168MB/s transfers
da1: 17359MB (35553120 512 byte sectors: 255H 32S/T 4357C)
da2 at ciss1 bus 0 target 0 lun 0
da2: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da2: 135.168MB/s transfers
da2: 138919MB (284506560 512 byte sectors: 255H 32S/T 34866C)
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/da0s1a
WARNING: / was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
bge0: link state changed to UP
bge1: link state changed to UP
# diff -ub GENERIC newspeer
--- GENERIC Fri Oct 28 21:21:27 2005
+++ newspeer Mon Nov 21 14:02:53 2005
@@ -19,10 +19,10 @@
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.429.2.4 2005/10/28 19:21:27 jhb
Exp $
machine i386
-cpu I486_CPU
-cpu I586_CPU
+#cpu I486_CPU
+#cpu I586_CPU
cpu I686_CPU
-ident GENERIC
+ident newspeer
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for
devices.
@@ -33,7 +33,7 @@
options SCHED_4BSD # 4BSD scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
-options INET6 # IPv6 communications protocols
+#options INET6 # IPv6 communications protocols
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
@@ -62,6 +62,11 @@
options AHD_REG_PRETTY_PRINT # Print register bitfields in
debug
# output. Adds ~215k to driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.
+
+options DEVICE_POLLING
+
+# To make an SMP kernel, the next line is needed
+options SMP # Symmetric MultiProcessor Kernel
device apic # I/O APIC
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051123134710.G57888>