Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 24 Jan 2017 19:13:57 +0000
From:      Andrew Turner <andrew@fubar.geek.nz>
To:        Tom Vijlbrief <tvijlbrief@gmail.com>
Cc:        Mark Millard <markmi@dsl-only.net>, freebsd-arm <freebsd-arm@freebsd.org>
Subject:   Re: Arm64 stack issues (was Re: FreeBSD status for/on ODroid-C2?)
Message-ID:  <20170124191357.0ec0abfd@zapp>
In-Reply-To: <CAOQrpVfK-Dw_rSo_YVY5MT1wbc6Ah-Pj%2BWv8UGjeiUQ1b3%2B-mg@mail.gmail.com>
References:  <CAOQrpVfK-Dw_rSo_YVY5MT1wbc6Ah-Pj%2BWv8UGjeiUQ1b3%2B-mg@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
Can you try with r312703 and without the malloc.conf change? I think the
issue was because errno was stored just before some internal jemalloc
state in the bss and there was a bug where the setting of errno where
it would overwrite 32 bits of this state.

Andrew

On Fri, 20 Jan 2017 08:39:15 +0000
Tom Vijlbrief <tvijlbrief@gmail.com> wrote:

> I'm using the image from
> 
> http://www.raspbsd.org/pine64.html (thanks Brad)
> 
> After applying the jemalloc work around at the bottom of:
> 
> https://wiki.freebsd.org/arm64/rpi3
> 
> and the dynamic linker fix:
> 
> https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=214971
> 
> I could build most ports but not world because it does not use the
> /etc/malloc.conf setting.
> 
> Using:
> 
> MALLOC_CONF=tcache:false script bw.log make buildworld NO_CLEAN=YES
> -j2
> 
> I can do a build world but what is more interesting is that without
> the MALLOC_CONF setting I get a lot of:
> 
> gic0: Spurious interrupt detected: last irq: 27 on CPU3
> 
> These errors disappear when disabling tcache.
> 
> The jemalloc tcache allocates on the stack so this hints at a bad
> interaction between the interrupt stack frames and the application
> stack.
> 
> Op 17:35 ZO 2 Okt 2016 schreef Mark Millard <markmi@dsl-only.net>:
> 
> [Adding a clarification.]
> 
> On 2016-Oct-2, at 8:20 AM, Mark Millard <markmi@dsl-only.net> wrote:
> 
> > Thanks for the notes.
> >
> > On 2016-Oct-2, at 7:17 AM, Tom Vijlbrief <tvijlbrief[ at
> > ]gmail.com>  
> wrote:
> >>
> >> No change (at least in my tree) since my last report on this list  
> somewhere in May or June.
> >>
> >> The kernel boots with 4 cpus and working usb. I use an usb
> >> ethernet  
> device and usb disk with the root filesysteem. Compiling and running
> ports works, but a build world fails randomly with a memory access
> error eg after running 15 minutes.
> >
> > Sounds possibly similar to TARGET_ARCH=powerpc 's stack-handling
> > SVR4 ABI  
> violation when world is built by clang 3.8.0 (bad clang code
> generation). To get to the point of buildworld going through I had to
> change the kernel to provide a so-called "red-zone" on the stack
> during signal handling to protect the stack from being trashed.
> buildworld gets extensive signals (SIGCHLD) and so without the
> "red-zone" it would eventually get trashed addresses, far before
> getting near completion.
> 
> I see my wording was poor for indicating the staging: I was already
> running a powerpc world built with clang 3.8.0's bad powerpc code
> generation when I tried to buildworld and had the signal handling
> problems (stack usage conflicts). The "red-zone" kernel hack allowed
> such buildworld activity to reliably work despite the clang 3.8.0
> based bad code that was in use.
> 
> > [Context: buildkernel via gcc 4.2.1 but buildworld via clang
> > 3.8.0 .]
> >
> > [Side note: I've tried aarch64 releng/11.0 (first RELEASE's raw)
> > under  
> qemu on Ubuntu 16.04.1 on the ODroid-C2 but it gots periodic illegal
> instructions in very basic operation, no builds active.]
> >  
> >> I don't think it makes sense to work on this  until a freebsd rpi3
> >> arm64  
> port is officially supported...
> >
> > [FYI: http://ameridroid.com/products/raspberry-pi-2-model-b-1gb-ram
> > lists  
> the RPi2B as both "out of stock" and "discontinued" and has for some
> time.]
> >  
> >> Op zo 2 okt. 2016 15:04 schreef Mark Millard <markmi[ at
> >> ]dsl-only.net>: . . .
> >> Anything worth reporting on the ODroid-C2 details for FreeBSD:
> >> what  
> works, what does not, what needs to be done to boot FreeBSD, and so
> on? (I assume head [CURRENT-12 these days].)
> >>
> >>
> >> Looking around. . .
> >>
> >>
> >> https://github.com/tomtor/image-freebsd-c2
> >>
> >> seems to have last been updated on May 7 (vs.  
> https://github.com/tomtor/image-freebsd-pine64 's April 17).
> >>
> >>
> >> https://github.com/tomtor/freebsd/tree/tc2
> >>
> >> seems to have last been updated on June 17.  
> >  
> 
> ===
> Mark Millard
> markmi at dsl-only.net
> 
> _______________________________________________
> freebsd-arm@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
> _______________________________________________
> freebsd-arm@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
> 




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20170124191357.0ec0abfd>