Date: Fri, 4 Jun 2010 01:19:32 -0700 (PDT) From: bored to death <bored_to_death85@yahoo.com> To: Luigi Rizzo <rizzo@iet.unipi.it> Cc: freebsd-ipfw <freebsd-ipfw@freebsd.org> Subject: Re: traffic bandwidth limit with dummynet Message-ID: <360703.24596.qm@web59711.mail.ac4.yahoo.com> In-Reply-To: <20100603172733.GA16454@onelab2.iet.unipi.it> References: <247123.29322.qm@web59713.mail.ac4.yahoo.com> <20100603172733.GA16454@onelab2.iet.unipi.it>
next in thread | previous in thread | raw e-mail | index | archive | help
thank you luigi for your reply, it helped.
i changed the hz parameter to 1000 and then 4000 and then 8000 in my /boot/loader.conf. the result got much better.
i configured my system as a router and i send 1GB traffic rate passing by it and set an 800MBytes bandwidth limit on input traffic with dummynet.
this was the result:
with hz=1 (default) between 200MBytes/s and 300MBytes/s
with hz=1000 between 200MBytes/s and 300MBytes/s
with hz=4000 between 350MBytes/s and 450MBytes/s
with hz=8000 between 250MBytes/s and 550MBytes/s
the maximum traffic rate is got so much better, but 2 problems still remain:
1- the maximum rate is still not high enough.
2- the rate variation range is high (250-550) and it's not a steady enough.
i've also tried setting different "queue" and "burst" values for the pipe. the result is a little better when i set "queue" to a value between 80MBytes and 90MBytes and "burst" to a big number.
any other ideas?
________________________________
From: Luigi Rizzo <rizzo@iet.unipi.it>
To: bored to death <bored_to_death85@yahoo.com>
Cc: freebsd-ipfw <freebsd-ipfw@freebsd.org>
Sent: Thu, June 3, 2010 9:57:33 PM
Subject: Re: traffic bandwidth limit with dummynet
On Thu, Jun 03, 2010 at 09:29:20AM -0700, bored to death wrote:
> hello,
>
> i'm trying to limit my input traffic bandwidth on freebsd. i used
> ipfw+dummynet. without limitation, i have almost 1Gbit/s input traffic
> on my system. when i try to limit the bandwidth, it works fine on low
> to normal limitation number (up to 450 Mbit/s).
> but when i limit my traffic to an amount bigger than 500MBit/s, my
> input traffic lowers down to average of 430 MBit/s. no matter what
> limitations i set(from 500MBit/s to 1000MBit/s) my input traffic rate
> is getting stucked at 430MBit/s.
try to run the kernel with higher value of HZ (in /boot/loader.conf
kern.hz=4000
and see if the situation improves.
I think the symptoms you are seeing depend on the fact that
packets are released every 1/HZ seconds probably causing some
queue overflow at high packet rates and [relatively] low HZ
values.
cheers
luigi
> i suspected low hardware performance, so i tried this on 2 different
> systems with freebsd-8.0 and the result is exactly the same.
>
> my ipfw rules are:
>
> Code:
> ipfw -q flush
> ipfw -q add 500 set 1 pipe 1 all from any to any in
> ipfw pipe 1 config bw 700Mbit/s
> ipfw add 1000 allow all from any to anyso my question is:
> 1- is ipfw+dummynet traffic limit control, has performance problem that
> cannot limit traffic correctly if limitation number is bigger than
> 500MBit/s?
> 2- is there any other way (other than ipfw+dummynet) to limit input bandwidth in freebsd?
>
> thank you.
>
>
>
> _______________________________________________
> freebsd-ipfw@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-ipfw
> To unsubscribe, send any mail to "freebsd-ipfw-unsubscribe@freebsd.org"
_______________________________________________
freebsd-ipfw@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-ipfw
To unsubscribe, send any mail to "freebsd-ipfw-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?360703.24596.qm>