Date: Mon, 18 Jan 2010 10:05:53 -0500 From: Charles Owens <cowens@greatbaysoftware.com> To: freebsd-hardware@freebsd.org Subject: Minute+ delay between kernel load and initialization Message-ID: <4B5478D1.4000900@greatbaysoftware.com>
next in thread | raw e-mail | index | archive | help
Hello,
We have a new system based on the Intel S5520 motherboard that seems to
work fine except during _every_ boot it pauses for about one minute 15
seconds just before any kernel initialization messages appear. We see
the loader appearing to complete its work (the kernel is loaded) and
then... it sits. Once it starts up again (with usual kernel-boot
messages) it appears to boot normally (no error messages).
This has been seen with both FreeBSD 8.0 and 7.1, using GENERIC kernels.
I'd appreciate any and all assistance in figuring this out.
Boot output follows (happens to be from a PAE-enabled kernel)
Thank you,
Charles
# again... we see this output immediately _after_ the delay ends:
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE-p5 #2: Fri Dec 18 15:03:26 UTC 2009
cowens@n_newcastle.greatbaysoftware.com:/usr/obj/usr/src/sys/BEACON
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz (1995.01-MHz
686-class CPU)
Origin = "GenuineIntel" Id = 0x106a5 Stepping = 5
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x9ce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT>
AMD Features=0x28100000<NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
Cores per package: 8
Logical CPUs per core: 2
real memory = 8321499136 (7936 MB)
avail memory = 6206566400 (5919 MB)
ACPI APIC Table: <INTEL S5520UR >
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 2
cpu2 (AP): APIC ID: 4
cpu3 (AP): APIC ID: 6
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
lapic0: Forcing LINT1 to edge trigger
registered firmware set <isp_1040>
registered firmware set <isp_1040_it>
registered firmware set <isp_1080>
registered firmware set <isp_1080_it>
registered firmware set <isp_12160>
registered firmware set <isp_12160_it>
registered firmware set <isp_2100>
registered firmware set <isp_2200>
registered firmware set <isp_2300>
registered firmware set <isp_2322>
registered firmware set <isp_2400>
kbd1 at kbdmux0
acpi0: <INTEL S5520UR> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 28 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
igb0: <Intel(R) PRO/1000 Network Connection version - 1.4.1> port
0x3020-0x303f mem 0xb1b20000-0xb1b3ffff,0xb1b44000-0xb1b47fff irq 40 at
device 0.0 on pci1
igb0: Using MSIX interrupts with 6 vectors
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: Ethernet address: 00:15:17:ac:52:2d
igb1: <Intel(R) PRO/1000 Network Connection version - 1.4.1> port
0x3000-0x301f mem 0xb1b00000-0xb1b1ffff,0xb1b40000-0xb1b43fff irq 28 at
device 0.1 on pci1
igb1: Using MSIX interrupts with 6 vectors
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: Ethernet address: 00:15:17:ac:52:2c
pcib2: <ACPI PCI-PCI bridge> irq 24 at device 3.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <PCI-PCI bridge> at device 0.0 on pci2
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 2.0 on pci3
pci4: <PCI bus> on pcib4
em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x2020-0x203f mem
0xb1a60000-0xb1a7ffff,0xb1a40000-0xb1a5ffff irq 36 at device 0.0 on pci4
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:15:17:c6:79:60
em1: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x2000-0x201f mem
0xb1a20000-0xb1a3ffff,0xb1a00000-0xb1a1ffff irq 35 at device 0.1 on pci4
em1: Using MSI interrupt
em1: [FILTER]
em1: Ethernet address: 00:15:17:c6:79:61
pcib5: <PCI-PCI bridge> at device 4.0 on pci3
pci5: <PCI bus> on pcib5
em2: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x1020-0x103f mem
0xb1960000-0xb197ffff,0xb1940000-0xb195ffff irq 34 at device 0.0 on pci5
em2: Using MSI interrupt
em2: [FILTER]
em2: Ethernet address: 00:15:17:c6:79:62
em3: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0x1000-0x101f mem
0xb1920000-0xb193ffff,0xb1900000-0xb191ffff irq 24 at device 0.1 on pci5
em3: Using MSI interrupt
em3: [FILTER]
em3: Ethernet address: 00:15:17:c6:79:63
pcib6: <ACPI PCI-PCI bridge> irq 32 at device 9.0 on pci0
pci6: <ACPI PCI bus> on pcib6
pcib7: <ACPI PCI-PCI bridge> irq 33 at device 10.0 on pci0
pci7: <ACPI PCI bus> on pcib7
pci0: <base peripheral, interrupt controller> at device 16.0 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 16.1 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 17.0 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 17.1 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.0 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.1 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.2 (no driver
attached)
pci0: <base peripheral, interrupt controller> at device 20.3 (no driver
attached)
pci0: <base peripheral> at device 22.0 (no driver attached)
pci0: <base peripheral> at device 22.1 (no driver attached)
pci0: <base peripheral> at device 22.2 (no driver attached)
pci0: <base peripheral> at device 22.3 (no driver attached)
pci0: <base peripheral> at device 22.4 (no driver attached)
pci0: <base peripheral> at device 22.5 (no driver attached)
pci0: <base peripheral> at device 22.6 (no driver attached)
pci0: <base peripheral> at device 22.7 (no driver attached)
uhci0: <UHCI (generic) USB controller> port 0x40e0-0x40ff irq 19 at
device 26.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x40c0-0x40df irq 19 at
device 26.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x40a0-0x40bf irq 19 at
device 26.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb1c22000-0xb1c223ff irq
19 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib8: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci8: <ACPI PCI bus> on pcib8
pcib9: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci9: <ACPI PCI bus> on pcib9
vgapci0: <VGA-compatible display> mem
0xb0000000-0xb0ffffff,0xb1800000-0xb1803fff,0xb1000000-0xb17fffff irq 16
at device 0.0 on pci9
pcib10: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci10: <ACPI PCI bus> on pcib10
uhci3: <UHCI (generic) USB controller> port 0x4080-0x409f irq 16 at
device 29.0 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0x4060-0x407f irq 16 at
device 29.1 on pci0
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
uhci5: <UHCI (generic) USB controller> port 0x4040-0x405f irq 16 at
device 29.2 on pci0
uhci5: [GIANT-LOCKED]
uhci5: [ITHREAD]
usb6: <UHCI (generic) USB controller> on uhci5
usb6: USB revision 1.0
uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub6: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xb1c21000-0xb1c213ff irq
16 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb7: EHCI version 1.0
usb7: companion controllers, 2 ports each: usb4 usb5 usb6
usb7: <EHCI (generic) USB 2.0 controller> on ehci1
usb7: USB revision 2.0
uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb7
uhub7: 6 ports with 6 removable, self powered
pcib11: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci11: <ACPI PCI bus> on pcib11
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel AHCI controller> port
0x4108-0x410f,0x4114-0x4117,0x4100-0x4107,0x4110-0x4113,0x4020-0x403f
mem 0xb1c20000-0xb1c207ff irq 18 at device 31.2 on pci0
atapci0: [ITHREAD]
atapci0: AHCI Version 01.20 controller with 6 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: port not implemented
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: port not implemented
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ata6: <ATA channel 4> on atapci0
ata6: port not implemented
ata6: [ITHREAD]
ata7: <ATA channel 5> on atapci0
ata7: port not implemented
ata7: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on
acpi0
sio1: type 16550A, console
sio1: [FILTER]
ipmi0: <IPMI System Interface> port 0xca2,0xca3 on acpi0
ipmi0: KCS mode found at io 0xca2 on acpi
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
device_attach: acpi_perf1 attach returned 6
device_attach: acpi_perf1 attach returned 6
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2: <ACPI CPU> on acpi0
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3: <ACPI CPU> on acpi0
device_attach: acpi_perf3 attach returned 6
device_attach: acpi_perf3 attach returned 6
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xca7ff,0xca800-0xcb7ff,0xcb800-0xcc7ff pnpid
ORM0000 on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ukbd0: <American Megatrends Inc. Virtual Keyboard and Mouse, class 0/0,
rev 1.10/1.00, addr 2> on uhub2
kbd0 at ukbd0
ums0: <American Megatrends Inc. Virtual Keyboard and Mouse, class 0/0,
rev 1.10/1.00, addr 2> on uhub2
ums0: X report 0x0002 not supported
device_attach: ums0 attach returned 6
uhub8: <vendor 0x0557 product 0x8021, class 9/0, rev 1.10/1.00, addr 2>
on uhub5
uhub8: 4 ports with 4 removable, self powered
ukbd1: <ATEN International Co. Ltd GCS1808 V3.0.294, class 0/0, rev
1.10/1.00, addr 3> on uhub8
kbd2 at ukbd1
uhid0: <ATEN International Co. Ltd GCS1808 V3.0.294, class 0/0, rev
1.10/1.00, addr 3> on uhub8
ums0: <ATEN International Co. Ltd GCS1808 V3.0.294, class 0/0, rev
1.10/1.00, addr 3> on uhub8
ums0: 5 buttons and Z dir.
ums1: <ATEN International Co. Ltd GCS1808 V3.0.294, class 0/0, rev
1.10/1.00, addr 3> on uhub8
ums1: X report 0x0002 not supported
device_attach: ums1 attach returned 6
Timecounters tick every 1.000 msec
ad4: 238475MB <Seagate ST3250310NS SN06> at ata2-master SATA300
acd0: DVDROM <TSSTcorpDVD-ROM TS-L333A/UO01> at ata5-master SATA150
ipmi0: GEOM_JOURNAL: Journal 173943913: ad4s1a contains data.
GEOM_JOURNAL: Journal 173943913: ad4s1a contains journal.IPMI device
rev. 1, firmware rev. 0.2, version 2.0
GEOM_JOURNAL: Journal ad4s1a clean.
ipmi0: Number of channels 2
ipmi0: Attached watchdog
lapic4: Forcing LINT1 to edge trigger
SMP: AP CPU #2 Launched!
lapic6: Forcing LINT1 to edge trigger
SMP: AP CPU #3 Launched!
lapic2: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
GEOM_JOURNAL: Journal 3858085586: ad4s1d contains data.
GEOM_JOURNAL: Journal 3858085586: ad4s1d contains journal.
GEOM_JOURNAL: Journal ad4s1d clean.
WARNING: Expected rawoffset 0, found 63
Trying to mount root from ufs:/dev/ad4s1a.journal
--
Charles Owens
Great Bay Software, Inc.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4B5478D1.4000900>