Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 16 Sep 2011 22:21:32 -0700
From:      Julian Elischer <julian@freebsd.org>
To:        Joshua Boyd <boydjd@jbip.net>
Cc:        Jason Usher <jusher71@yahoo.com>, "freebsd-fs@freebsd.org" <freebsd-fs@freebsd.org>
Subject:   Re: ZFS obn FreeBSD hardware model for 48 or 96 sata3 paths...
Message-ID:  <4E742E5C.2010900@freebsd.org>
In-Reply-To: <CAHcKe7kfdirJL-vPw=pnFvtzo7ZouDQNPkLVbKs_s35Amz40NQ@mail.gmail.com>
References:  <1316222526.31565.YahooMailNeo@web121205.mail.ne1.yahoo.com> <CAHcKe7kfdirJL-vPw=pnFvtzo7ZouDQNPkLVbKs_s35Amz40NQ@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On 9/16/11 8:45 PM, Joshua Boyd wrote:
> On Fri, Sep 16, 2011 at 9:22 PM, Jason Usher<jusher71@yahoo.com>  wrote:
>
>> Hello,
>>
>> I am building my first FreeBSD based ZFS system and am deciding on a
>> hardware model.  The overriding requirement is:
>>
>> 1) immediately support 48 internal sata3 drives at full bandwidth - every
>> drive has independent path to CPU
>>
>> 2) future expansion to support another 48 drives on an attached JBOD, all
>> of which ALSO have their own independent path to CPU
>>
>> The first question is:  how many pcie 2.0 lanes does a motherboard need to
>> run 96 independent sata3 connections ?  Am I correct that this is extremely
>> important ?
>>
>> Next, I see a lot of implementations done with LSI adaptors - is this as
>> simple as choosing (3) LSI SAS 9201-16i for the 48 internal drives and (3)
>> LSI SAS 9201-16e for the external drives ?  I remember that these cards are
>> supported with mps(4) in FreeBSD, but only in 9.x (?) - is that still the
>> case, or is that support in 8.2 or later in 8.3 ?
>>
>> So I will boot of a pair of mirrored SSDs formatted UFS2 - easy.  But I
>> would also like to spec and use a ZIL+L2ARC and am not sure where to go ...
>> the system will be VERY write-biased and use a LOT of inodes - so lots of
>> scanning of large dirs with lots of inodes and writing data.  Something like
>> 400 million inodes on a filesystem with an average file size of 150 KB.
>>
>> - can I just skip the l2arc and just add more RAM ?  Wouldn't the RAM
>> always be faster/better ?  Or do folks build such large L2arcs (4x200 GB SSD
>> ?) that it outweighs an extra 32 GB of RAM ?
>>
>> - provided I maintain the free pcie slot(s) and/or free 2.5" drive slots,
>> can I always just add a ZIL after the fact ?  I'd prefer to skip it for now
>> and save that complexity for later...
>>
>> Thanks very much for any comments/suggestions.
>>
>> _______________________________________________
>> freebsd-fs@freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-fs
>> To unsubscribe, send any mail to "freebsd-fs-unsubscribe@freebsd.org"
>>
> I've built something similar, using 3 Supermicro SC933 chassis, 2 HP SAS
> expanders, 2 AOC-USAS-L8i cards, and 1 card with 2 external ports (I can't
> remember the exact name, but it's an LSI chipset card). This is a 45 drive
> capable setup, so smaller than what you're wanting.
>
> I'd recommend you get two of these:
>
> http://www.supermicro.com/products/chassis/4U/847/SC847E26-RJBOD1.cfm
>
> That gives you 90 drives in 8U. They each have dual port expanders
> integrated to the backplanes. Then build a separate 1 or 2u box that holds
> your boot drives/cache drives. In this box put in 2 6Gb cards with external
> SAS connectors. Something like the 9750-8E, which are 6Gbit/s cards and
> support drives bigger than 2TB. You'll need to run 8-STABLE, as these cards
> use the mptsas driver, which isn't in 8-RELEASE last I checked.
>
> I don't have any experience with separate cache/log devices, so I can't
> offer much advice there.
>

what is it you are trying to achieve?  large storage, or high 
transaction rates? (or both?)

I'm biased but I'd put a 160GB zil on a fusion-io card   and dedicate 
8G of the ram to it's useage.

it's remarkable what a 20uSec turnaround time on your metadata can do..






Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4E742E5C.2010900>