Date: Mon, 16 Jun 2014 08:55:01 +0200 From: Hans Petter Selasky <hps@selasky.org> To: Matthias Apitz <guru@unixarea.de> Cc: freebsd-usb@freebsd.org Subject: Re: Fwd: USB to parallel for printer HP LaserJet 4mL Message-ID: <539E94C5.50405@selasky.org> In-Reply-To: <20140616065050.GA1552@La-Habana> References: <20140602150802.GA1950@La-Habana> <538C9A83.7050606@selasky.org> <20140610054403.GA1589@La-Habana> <539964AB.1030909@selasky.org> <20140613184921.GA1748@La-Habana> <539BEE2E.9050108@selasky.org> <20140614181138.GA1598@La-Habana> <539C9181.10304@selasky.org> <20140616054141.GA1358@La-Habana> <539E87EF.9080404@selasky.org> <20140616065050.GA1552@La-Habana>
next in thread | previous in thread | raw e-mail | index | archive | help
On 06/16/14 08:50, Matthias Apitz wrote: > El día Monday, June 16, 2014 a las 08:00:15AM +0200, Hans Petter Selasky escribió: > >> Hi, >> >> Can you also use only the no-reset version: /dev/unlpt0 ? >> >> Make sure device is power cycled first. > > Hi, > > I did > > - detached USB cable > - power cycled device > - wait until device ready > > # kldunload ulpt.ko > # kldload modules/usb/ulpt/ulpt.ko > # sysctl hw.usb.ulpt.debug=15 > hw.usb.ulpt.debug: 0 -> 15 > > - now pluged in the USB cable > > # date > /dev/unlpt0 > ^C > # date > lunes, 16 de junio de 2014, 08:44:49 CEST > # > > messages are attached; thx > > Jun 16 08:44:02 La-Habana root: Unknown USB device: vendor 0x0c45 product 0x62c0 bus uhub3 > Jun 16 08:44:02 La-Habana root: Unknown USB device: vendor 0x0c45 product 0x62c0 bus uhub3 > Jun 16 08:44:27 La-Habana kernel: ugen1.2: <Prlific Technology Inc.> at usbus1 > Jun 16 08:44:27 La-Habana kernel: ulpt_probe: > Jun 16 08:44:27 La-Habana kernel: ulpt_probe: > Jun 16 08:44:27 La-Habana kernel: ulpt_attach: sc=0xc596c580 > Jun 16 08:44:27 La-Habana kernel: ulpt0: <Prlific Technology Inc. IEEE-1284 Controller, class 0/0, rev 1.00/2.00, addr 2> on usbus1 > Jun 16 08:44:27 La-Habana kernel: ulpt_attach: setting alternate config number: 1 > Jun 16 08:44:27 La-Habana kernel: ulpt0: using bi-directional mode > Jun 16 08:44:27 La-Habana kernel: ulpt_watchdog: debugging ulpt.c: ulpt_watchdog() skiped read status > Jun 16 08:44:33 La-Habana last message repeated 6 times > Jun 16 08:44:34 La-Habana kernel: ulpt_write_callback: state=0x0 actlen=0 > Jun 16 08:44:34 La-Habana kernel: ulpt_watchdog: debugging ulpt.c: ulpt_watchdog() skiped read status > Jun 16 08:44:47 La-Habana last message repeated 13 times > Jun 16 08:44:48 La-Habana kernel: ulpt0: at uhub1, port 1, addr 2 (disconnected) > Jun 16 08:44:48 La-Habana kernel: ulpt_detach: sc=0xc596c580 > Jun 16 08:44:48 La-Habana kernel: ulpt_write_callback: state=0x2 actlen=0 > Jun 16 08:44:49 La-Habana kernel: ulpt_probe: > Jun 16 08:44:49 La-Habana kernel: ulpt_probe: > Jun 16 08:44:49 La-Habana kernel: ulpt_attach: sc=0xc5839880 > Jun 16 08:44:49 La-Habana kernel: ulpt0: <Prlific Technology Inc. IEEE-1284 Controller, class 0/0, rev 1.00/2.00, addr 2> on usbus1 > Jun 16 08:44:49 La-Habana kernel: ulpt_attach: setting alternate config number: 1 > Jun 16 08:44:49 La-Habana kernel: ulpt0: using bi-directional mode > Jun 16 08:44:49 La-Habana kernel: ulpt_watchdog: debugging ulpt.c: ulpt_watchdog() skiped read status > Jun 16 08:44:53 La-Habana last message repeated 4 times > Jun 16 08:44:54 La-Habana kernel: ulpt_watchdog: debugging ulpt.c: ulpt_watchdog() skiped read status > > matthias > Hi, If you disconnect the LPT port from the printer and repeat? Is the device sufficiently powered? --HPS
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?539E94C5.50405>