Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 4 Apr 2016 14:02:23 +0300
From:      Daniel Braniss <danny@cs.huji.ac.il>
To:        Erik Moe <e.moe@rcn.com>
Cc:        freebsd-arm <freeBSD-arm@freebsd.org>
Subject:   Re: Odroidc1+  stuck booting
Message-ID:  <77D2CAED-B44A-4602-8C70-C3DD0A8D089C@cs.huji.ac.il>
In-Reply-To: <F5CCEBD7-0C43-415C-97E5-35BEC63BEDC6@rcn.com>
References:  <687E2129-BE66-4CC9-9B30-D8DFB7A2FEF6@cs.huji.ac.il> <982FE02C-7BEC-4CA0-BCAE-FE6CC5C9CFB4@rcn.com> <B39CD871-7BE5-44EA-816A-42A80E34D8A7@rcn.com> <EEAFAE63-3550-4862-924C-B8E7B68FC62E@cs.huji.ac.il> <CCC86C18-EE51-4A24-A9A1-4FDCBB28B198@cs.huji.ac.il> <F5CCEBD7-0C43-415C-97E5-35BEC63BEDC6@rcn.com>

next in thread | previous in thread | raw e-mail | index | archive | help
I assume you have a C1 not a C1+, because I=E2=80=99m doing the same,
and no luck. I know that the board is ok because It boots and runs =
Daisuke-san=E2=80=99s  image.
danny

> On 31 Mar 2016, at 15:29, Erik Moe <e.moe@rcn.com> wrote:
>=20
> Everything I=E2=80=99m doing I =E2=80=9Cborrowed=E2=80=9D from here:  =
https://wiki.freebsd.org/FreeBSD/arm/Odroid-C1
>=20
> I=E2=80=99m using the stock ODROIDC1 kernel config in head which =
builds the FTD statically into the kernel from =
src/sys/boot/fdt/dts/arm/odroidc1.dts. I liberated u-boot from =
ArchLinuxARM-odroid-c1-latest.tar.gz.  My boot.ini is simply this:
>=20
> ODROIDC-UBOOT-CONFIG
>=20
> setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000"
> run bootcmd
>=20
> Erik
>=20
>> On Mar 31, 2016, at 1:36 AM, Daniel Braniss <danny@cs.huji.ac.il> =
wrote:
>>=20
>> oh, and if you feel generous your ODROIDC1.conf =E2=80=A6
>> thanks,
>> 	danny
>>=20
>>> On 31 Mar 2016, at 09:31, Daniel Braniss <danny@cs.huji.ac.il> =
wrote:
>>>=20
>>> hi Erik,
>>> can you send me your
>>> 	uboot
>>> 	boot.ini
>>> 	*.dtb
>>> I=E2=80=99m pretty sure the issue is somewhere there then.
>>> thanks,
>>> 	danny
>>>=20
>>>> On 31 Mar 2016, at 09:11, Erik Moe <e.moe@rcn.com> wrote:
>>>>=20
>>>> I built a new image for my odriod-c1 for ssd from the latest =
sources and had no issues and didn=E2=80=99t need to tweet anything.  I =
don=E2=80=99t have and odriod-c1+, but my understanding is there isn=E2=80=
=99t much difference between the two.  I am using the serial console.
>>>>=20
>>>> =
QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PA=
SS:1;
>>>> =
-----------------------------------------------------------------------
>>>> * Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec  8 =
2014) *
>>>> =
-----------------------------------------------------------------------
>>>> CPU : AMLogic S805
>>>> MEM : 1024MB (DDR3@792MHz)
>>>> BID : HKC13C0001
>>>> S/N : HKC1CC037EBE4620
>>>> 0x0000009f
>>>> check SD_boot_type:0x1   card_type:0x1
>>>> Loading U-boot...success.
>>>>=20
>>>>=20
>>>> U-boot(odroidc@) (Jun 12 2015 - 17:31:14)
>>>>=20
>>>> DRAM:  1 GiB
>>>> relocation Offset is: 2ff1c000
>>>> MMC:   SDCARD: 0, eMMC: 1
>>>> IR init is done!
>>>> vpu clk_level =3D 3
>>>> set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
>>>> mode =3D 6  vic =3D 4
>>>> set HDMI vic: 4
>>>> mode is: 6
>>>> viu chan =3D 1
>>>> config HPLL
>>>> config HPLL done
>>>> reconfig packet setting done
>>>> MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks =
read: OK
>>>> There is no valid bmp file at the given address
>>>> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>>> Vendor: Man 035344 Snr 29cfee4e Rev: 8.0 Prod: SL08G
>>>>         Type: Removable Hard Disk
>>>>         Capacity: 7580.0 MB =3D 7.4 GB (15523840 x 512)
>>>> ------------------------------------------------------------
>>>> Partition     Start Sector     Num Sectors     Type
>>>> 1                 1134          131040       6
>>>> 2               132174        15391666      a5
>>>> =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>>> Net:   Meson_Ethernet
>>>> init suspend firmware done. (ret:0)
>>>> Hit Enter key to stop autoboot -- :  0
>>>> exit abortboot: 0
>>>> reading boot.ini
>>>>=20
>>>> 98 bytes read
>>>> Loading boot.ini from mmc0:1 (vfat)
>>>> Executing the script...
>>>> setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000"
>>>> run bootcmd
>>>> reading kernel.bin
>>>>=20
>>>> 6055396 bytes read
>>>> ## Starting application at 0x00100000 ...
>>>> ARM Debug Architecture v7
>>>> 2 watchpoints and 3 breakpoints supported
>>>> KDB: debugger backends: ddb
>>>> KDB: current backend: ddb
>>>> Copyright (c) 1992-2016 The FreeBSD Project.
>>>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, =
1994
>>>>     The Regents of the University of California. All rights =
reserved.
>>>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>>>> FreeBSD 11.0-CURRENT #4 43026a8(master)-dirty: Thu Mar 31 04:14:32 =
CDT 2016
>>>> =
root@dora:/usr/home/emoe/Projects/ARM/odroid-c1/obj/arm.armv6hf/usr/home/e=
moe/Projects/ARM/src/sys/ODROIDC1 arm
>>>> FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based =
on LLVM 3.8.0)
>>>> WARNING: WITNESS option enabled, expect reduced performance.
>>>> VT: init without driver.
>>>> Preloaded elf kernel "kernel" at 0xc07c5d6c.
>>>> CPU: Cortex A5 rev 1 (Cortex-A core)
>>>> Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 =
Security_Ext
>>>> WB enabled LABT branch prediction disabled
>>>> LoUU:2 LoC:2 LoUIS:2
>>>> Cache level 1:
>>>> 32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
>>>> 32KB/32B 2-way instruction cache Read-Alloc
>>>> real memory  =3D 1073737728 (1023 MB)
>>>> avail memory =3D 1038233600 (990 MB)
>>>> Physical memory chunk(s):
>>>> 0x00001000 - 0x3fffffff,  1023 MB ( 262143 pages)
>>>> Excluded memory regions:
>>>> 0x00100000 - 0x00853fff,     7 MB (   1876 pages) NoAlloc
>>>> Static device mappings:
>>>> 0xc1100000 - 0xc12fffff mapped at VA 0xffd00000
>>>> 0xc4200000 - 0xc42fffff mapped at VA 0xffc00000
>>>> 0xc4300000 - 0xc43fffff mapped at VA 0xffb00000
>>>> 0xc8000000 - 0xc80fffff mapped at VA 0xffa00000
>>>> 0xc8100000 - 0xc81fffff mapped at VA 0xff900000
>>>> 0xc9000000 - 0xc97fffff mapped at VA 0xff100000
>>>> 0xd9000000 - 0xd90fffff mapped at VA 0xff000000
>>>> 0xda000000 - 0xda0fffff mapped at VA 0xfef00000
>>>> Amlogic aml8726-m8b SoC
>>>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>>>> ULE: setup cpu 0
>>>> ULE: setup cpu 1
>>>> ULE: setup cpu 2
>>>> ULE: setup cpu 3
>>>> random: entropy device external interface
>>>> null: <full device, null device, zero device>
>>>> openfirm: <Open Firmware control device>
>>>> mem: <memory>
>>>> nfslock: pseudo-device
>>>> crypto: <crypto core>
>>>> random: harvesting attach, 8 bytes (4 bits) from nexus0
>>>> ofwbus0: <Open Firmware Device Tree>
>>>> simplebus0: <Flattened device tree simple bus> on ofwbus0
>>>> random: harvesting attach, 8 bytes (4 bits) from simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from ofwbus0
>>>> clkmsr0: <Amlogic aml8726 clkmsr> mem 0xc1108758-0xc1108767 on =
simplebus0
>>>> clkmsr0: bus clock 159 MHz
>>>> random: harvesting attach, 8 bytes (4 bits) from clkmsr0
>>>> l2cache0: <PL310 L2 cache controller> mem 0xc4200000-0xc4200fff irq =
0 on ofwbus0
>>>> l2cache0: Part number: 0x3, release: 0x9
>>>> l2cache0: L2 Cache enabled: 512KB/32B 8 ways
>>>> l2cache0: Early BRESP response: disabled
>>>> l2cache0: Instruction prefetch: disabled
>>>> l2cache0: Data prefetch: enabled
>>>> l2cache0: Non-secure interrupt control: disabled
>>>> l2cache0: Non-secure lockdown: disabled
>>>> l2cache0: Share override: disabled
>>>> l2cache0: Double linefill: disabled
>>>> l2cache0: Instruction prefetch: disabled
>>>> l2cache0: Data prefetch: enabled
>>>> l2cache0: Double linefill on WRAP request: disabled
>>>> l2cache0: Prefetch drop: disabled
>>>> l2cache0: Incr double Linefill: disabled
>>>> l2cache0: Not same ID on exclusive sequence: disabled
>>>> l2cache0: Prefetch offset: 0
>>>> random: harvesting attach, 8 bytes (4 bits) from l2cache0
>>>> scu0: <ARM Snoop Control Unit> mem 0xc4300000-0xc4300fff on =
simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from scu0
>>>> cpuconfig0: <Amlogic CPU Config> mem 0xd901ff80-0xd901ff8f on =
simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from cpuconfig0
>>>> ccm0: <Amlogic aml8726 ccm> mem 0xc1104140-0xc1104153 on simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from ccm0
>>>> pinctrl0: <Amlogic aml8726 pinctrl> mem =
0xc11080b0-0xc11080d7,0xc11080e8-0xc11080ff,0xc1108120-0xc1108137,0xc81000=
14-0xc8100017,0xc810002c-0xc810002f,0xc810002c-0xc810002f on simplebus0
>>>> Processing 3 pin-config node(s) in pinctrl-0 for pinctrl@c11080b0
>>>> Processing 1 pin-config node(s) in pinctrl-0 for mmc@c1108c20
>>>> Processing 1 pin-config node(s) in pinctrl-0 for sdxc@c1108e00
>>>> random: harvesting attach, 8 bytes (4 bits) from pinctrl0
>>>> gic0: <ARM Generic Interrupt Controller> mem =
0xc4301000-0xc4301fff,0xc4300100-0xc43001ff on ofwbus0
>>>> ofwbus0: no default resources for rid =3D 0, type =3D 1
>>>> gic0: pn 0x390, arch 0x1, rev 0x1, implementer 0x43b irqs 256
>>>> random: harvesting attach, 8 bytes (4 bits) from gic0
>>>> wdt0: <Amlogic aml8726 WDT> mem 0xc1109900-0xc1109907 irq 2 on =
simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from wdt0
>>>> timer0: <Amlogic aml8726 timer> mem 0xc1109940-0xc1109957 irq 1 on =
ofwbus0
>>>> Event timer "aml8726 timer A" frequency 1000000 Hz quality 1000
>>>> Timecounter "aml8726 timer E" frequency 1000000 Hz quality 1000
>>>> random: harvesting attach, 8 bytes (4 bits) from timer0
>>>> uart0: <Amlogic aml8726 UART> mem 0xc81004c0-0xc81004d7 irq 3 on =
simplebus0
>>>> uart0: RTS iflow, CTS oflow
>>>> uart0: console (115200,n,8,1)
>>>> uart0: fast interrupt
>>>> uart0: PPS capture mode: DCDinvalid
>>>> random: harvesting attach, 8 bytes (4 bits) from uart0
>>>> uart1: <Amlogic aml8726 UART> mem 0xc11084c0-0xc11084d7 irq 4 on =
simplebus0
>>>> uart1: RTS iflow, CTS oflow
>>>> uart1: fast interrupt
>>>> uart1: PPS capture mode: DCDinvalid
>>>> random: harvesting attach, 8 bytes (4 bits) from uart1
>>>> uart2: <Amlogic aml8726 UART> mem 0xc11084dc-0xc11084f3 irq 5 on =
simplebus0
>>>> uart2: RTS iflow, CTS oflow
>>>> uart2: fast interrupt
>>>> uart2: PPS capture mode: DCDinvalid
>>>> random: harvesting attach, 8 bytes (4 bits) from uart2
>>>> uart3: <Amlogic aml8726 UART> mem 0xc1108700-0xc1108717 irq 6 on =
simplebus0
>>>> uart3: RTS iflow, CTS oflow
>>>> uart3: fast interrupt
>>>> uart3: PPS capture mode: DCDinvalid
>>>> random: harvesting attach, 8 bytes (4 bits) from uart3
>>>> simplebus0: <i2c@c8100500> mem 0xc8100500-0xc810051f irq 7 disabled =
compat amlogic,meson6-i2c (no driver attached)
>>>> aml8726_iic0: <Amlogic aml8726 I2C> mem 0xc1108500-0xc110851f irq 8 =
on simplebus0
>>>> iicbb0: <I2C bit-banging driver> on aml8726_iic0
>>>> iicbus0: <Philips I2C bus> on iicbb0 master-only
>>>> iic0: <I2C generic I/O> on iicbus0
>>>> random: harvesting attach, 8 bytes (4 bits) from iic0
>>>> random: harvesting attach, 8 bytes (4 bits) from iicbus0
>>>> random: harvesting attach, 8 bytes (4 bits) from iicbb0
>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic0
>>>> aml8726_iic1: <Amlogic aml8726 I2C> mem 0xc11087c0-0xc11087df irq 9 =
on simplebus0
>>>> iicbb1: <I2C bit-banging driver> on aml8726_iic1
>>>> iicbus1: <Philips I2C bus> on iicbb1 master-only
>>>> iic1: <I2C generic I/O> on iicbus1
>>>> random: harvesting attach, 8 bytes (4 bits) from iic1
>>>> random: harvesting attach, 8 bytes (4 bits) from iicbus1
>>>> random: harvesting attach, 8 bytes (4 bits) from iicbb1
>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_iic1
>>>> simplebus0: <ir-receiver@c8100480> mem 0xc8100480-0xc810049f irq 10 =
disabled compat amlogic,meson6-ir (no driver attached)
>>>> simplebus0: <spi@c1108c80> mem 0xc1108c80-0xc1108cff disabled =
compat amlogic,meson6-spifc (no driver attached)
>>>> simplebus0: <ethernet@c9410000> mem =
0xc9410000-0xc941ffff,0xc1108108-0xc110810b irq 11 disabled compat =
amlogic,meson6-dwmac (no driver attached)
>>>> rtc0: <Amlogic aml8726 RTC> mem 0xc8100740-0xc8100753 irq 12 on =
simplebus0
>>>> rtc0: crystal oscillator check failed
>>>> device_attach: rtc0 attach returned 6
>>>> gpio0: <Amlogic aml8726 GPIO> mem =
0xc8100024-0xc8100027,0xc8100024-0xc8100027,0xc8100028-0xc810002b on =
simplebus0
>>>> gpiobus0: <OFW GPIO bus> on gpio0
>>>> gpioled0: <GPIO led> at pin 13 on gpiobus0
>>>> random: harvesting attach, 8 bytes (4 bits) from gpioled0
>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus0
>>>> gpioc0: <GPIO controller> on gpio0
>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc0
>>>> random: harvesting attach, 8 bytes (4 bits) from gpio0
>>>> gpio1: <Amlogic aml8726 GPIO> mem =
0xc1108054-0xc1108057,0xc1108058-0xc110805b,0xc110805c-0xc110805f on =
simplebus0
>>>> gpiobus1: <OFW GPIO bus> on gpio1
>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus1
>>>> gpioc1: <GPIO controller> on gpio1
>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc1
>>>> random: harvesting attach, 8 bytes (4 bits) from gpio1
>>>> gpio2: <Amlogic aml8726 GPIO> mem =
0xc110806c-0xc110806f,0xc1108070-0xc1108073,0xc1108074-0xc1108077 on =
simplebus0
>>>> gpiobus2: <OFW GPIO bus> on gpio2
>>>> random: harvesting attach, 8 bytes (4 bits) from gpiobus2
>>>> gpioc2: <GPIO controller> on gpio2
>>>> random: harvesting attach, 8 bytes (4 bits) from gpioc2
>>>> random: harvesting attach, 8 bytes (4 bits) from gpio2
>>>> aml8726_mmc0: <Amlogic aml8726 MMC> mem 0xc1108c20-0xc1108c3f irq =
13 on simplebus0
>>>> mmc0: <MMC/SD bus> on aml8726_mmc0
>>>> random: harvesting attach, 8 bytes (4 bits) from mmc0
>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_mmc0
>>>> aml8726_sdxc0: <Amlogic aml8726-m8 SDXC> mem 0xc1108e00-0xc1108e3b =
irq 14 on simplebus0
>>>> mmc1: <MMC/SD bus> on aml8726_sdxc0
>>>> random: harvesting attach, 8 bytes (4 bits) from mmc1
>>>> random: harvesting attach, 8 bytes (4 bits) from aml8726_sdxc0
>>>> simplebus0: <rng@c1108100> mem 0xc1108100-0xc1108107 compat =
amlogic,aml8726-rng (no driver attached)
>>>> usbphy0: <Amlogic aml8726-m8 USB PHY> mem 0xc1108800-0xc110881f on =
simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from usbphy0
>>>> usbphy1: <Amlogic aml8726-m8 USB PHY> mem 0xc1108820-0xc110883f on =
simplebus0
>>>> random: harvesting attach, 8 bytes (4 bits) from usbphy1
>>>> dwcotg0: <DWC OTG 2.0 integrated USB controller> mem =
0xc9040000-0xc907ffff irq 15 on simplebus0
>>>> usbus0 on dwcotg0
>>>> dwcotg0: usbpf: Attached
>>>> random: harvesting attach, 8 bytes (4 bits) from usbus0
>>>> random: harvesting attach, 8 bytes (4 bits) from dwcotg0
>>>> dwcotg1: <DWC OTG 2.0 integrated USB controller> mem =
0xc90c0000-0xc90fffff irq 16 on simplebus0
>>>> usbus1 on dwcotg1
>>>> dwcotg1: usbpf: Attached
>>>> random: harvesting attach, 8 bytes (4 bits) from usbus1
>>>> random: harvesting attach, 8 bytes (4 bits) from dwcotg1
>>>> dwc0: <Amlogic Meson Gigabit Ethernet Controller> mem =
0xc9410000-0xc9411fff irq 11 on simplebus0
>>>> miibus0: <MII bus> on dwc0
>>>> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on =
miibus0
>>>> rgephy0: OUI 0x00e04c, model 0x0011, rev. 6
>>>> rgephy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT-FDX, 1000baseT-FDX-master, auto
>>>> random: harvesting attach, 8 bytes (4 bits) from rgephy0
>>>> rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on =
miibus0
>>>> rgephy1: OUI 0x00e04c, model 0x0011, rev. 6
>>>> rgephy1:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT-FDX, 1000baseT-FDX-master, auto
>>>> random: harvesting attach, 8 bytes (4 bits) from rgephy1
>>>> random: harvesting attach, 8 bytes (4 bits) from miibus0
>>>> dwc0: bpf attached
>>>> dwc0: Ethernet address: 62:73:64:5d:6a:ec
>>>> random: harvesting attach, 8 bytes (4 bits) from dwc0
>>>> fb0: <Amlogic aml8726 FB> mem =
0xc8006048-0xc8006053,0xc1106800-0xc1106bff,0xc1107400-0xc11077ff irq =
17,18,19,20 on simplebus0
>>>> fbd0 on fb0
>>>> VT: initialize with new VT driver "fb".
>>>> random: harvesting attach, 8 bytes (4 bits) from fbd0
>>>> random: harvesting attach, 8 bytes (4 bits) from fb0
>>>> cpulist0: <Open Firmware CPU Group> on ofwbus0
>>>> cpu0: <Open Firmware CPU> on cpulist0
>>>> cpu0: missing 'clock-frequency' property
>>>> random: harvesting attach, 8 bytes (4 bits) from cpu0
>>>> cpu1: <Open Firmware CPU> on cpulist0
>>>> cpu1: missing 'clock-frequency' property
>>>> random: harvesting attach, 8 bytes (4 bits) from cpu1
>>>> cpu2: <Open Firmware CPU> on cpulist0
>>>> cpu2: missing 'clock-frequency' property
>>>> random: harvesting attach, 8 bytes (4 bits) from cpu2
>>>> cpu3: <Open Firmware CPU> on cpulist0
>>>> cpu3: missing 'clock-frequency' property
>>>> random: harvesting attach, 8 bytes (4 bits) from cpu3
>>>> random: harvesting attach, 8 bytes (4 bits) from cpulist0
>>>> ofwbus0: <clk@0> compat fixed-clock (no driver attached)
>>>> ofwbus0: <leds> compat gpio-leds (no driver attached)
>>>> cryptosoft0: <software crypto>
>>>> crypto: assign cryptosoft0 driver id 0, flags 100663296
>>>> crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
>>>> crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
>>>> random: harvesting attach, 8 bytes (4 bits) from cryptosoft0
>>>> procfs registered
>>>> Timecounters tick every 10.000 msec
>>>> tcp_init: net.inet.tcp.tcbhashsize auto tuned to 8192
>>>> usbus0: 480Mbps High Speed USB v2.0
>>>> IPsec: Initialized Security Association Processing.
>>>> lo0: bpf attached
>>>> mmc0: Probing bus
>>>> usbus1: 480Mbps High Speed USB v2.0
>>>> mmc0: SD 2.0 interface conditions: OK
>>>> mmc0: SD probe: OK (OCR: 0x40ff8000)
>>>> mmc0: Current OCR: 0x00ff8000
>>>> ugen1.1: <DWCOTG> at usbus1
>>>> uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on =
usbus1
>>>> ugen0.1: <DWCOTG> at usbus0
>>>> uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on =
usbus0
>>>> mmc0: Probing cards
>>>> mmc0: New card detected (CID 035344534c3038478029cfee4e00f900)
>>>> mmc0: New card detected (CSD 400e00325b5900003b377f800a404000)
>>>> mmc0: Card at relative address 0xaaaa added:
>>>> mmc0:  card: SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD
>>>> mmc0:  bus: 4bit, 50MHz, high speed timing
>>>> mmc0:  memory: 15523840 blocks, erase sector 8192 blocks
>>>> mmc0: setting transfer rate to 39.750MHz (high speed timing)
>>>> mmcsd0: 8GB <SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD> at =
mmc0 39.7MHz/4bit/8-block
>>>> random: harvesting attach, 8 bytes (4 bits) from mmcsd0
>>>> mmc1: Probing bus
>>>> GEOM: new disk mmcsd0
>>>> mmc0: setting bus width to 4 bits
>>>> GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 =
bytes
>>>> GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 =
bytes
>>>> mmc1: SD probe: failed
>>>> mmc1: MMC probe: failed
>>>> mmc1: Current OCR: 0x00000000
>>>> mmc1: No compatible cards found on bus
>>>> Release APs
>>>> WARNING: WITNESS option enabled, expect reduced performance.
>>>> Trying to mount root from ufs:mmcsd0s2 []...
>>>> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 =
bytes
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not =
aligned on 4194304 bytes
>>>> warning: no time-of-day clock registered, system time will not be =
set accurately
>>>> start_init: trying /sbin/init
>>>> uhub0: 1 port with 1 removable, self powered
>>>> random: harvesting attach, 8 bytes (4 bits) from uhub0
>>>> uhub1: 1 port with 1 removable, self powered
>>>> random: harvesting attach, 8 bytes (4 bits) from uhub1
>>>> ugen1.2: <vendor 0x05e3> at usbus1
>>>> uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr =
2> on usbus1
>>>> uhub2: MTT enabled
>>>> Growing root partition to fill device
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not =
aligned on 4194304 bytes
>>>> mmcsd0s2 resized
>>>> growfs: superblock not recognized
>>>> /etc/rc: WARNING: hostid: unable to figure out a UUID from DMI =
data, generating a new one
>>>> uhub2: 4 ports with 4 removable, self powered
>>>> random: harvesting attach, 8 bytes (4 bits) from uhub2
>>>> Setting hostuuid: 214610b1-f72e-11e5-8203-df073412266c.
>>>> Setting hostid: 0x373425ad.
>>>> No suitable dump device was found.
>>>> Starting file system checks:
>>>> /dev/mmcsd0s2: FILE SYSTEM CLEAN; SKIPPING CHECKS
>>>> /dev/mmcsd0s2: clean, 36687 free (103 frags, 4573 blocks, 0.0% =
fragmentation)
>>>> GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 =
bytes
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not =
aligned on 4194304 bytes
>>>> GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not =
aligned on 4194304 bytes
>>>> Mounting local file systems:.
>>>> Setting hostname: freebsd.
>>>> Setting up =
harvesting:[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,K=
EYBOARD,ATTACH,CACHED
>>>> Feeding entropy:random: unblocking device.
>>>> .
>>>> dwc0: link state changed to DOWN
>>>> Starting Network: lo0 dwc0.
>>>> lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>>>>     options=3D600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
>>>>     inet6 ::1 prefixlen 128
>>>>     inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
>>>>     inet 127.0.0.1 netmask 0xff000000
>>>>     groups: lo
>>>>     nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
>>>> dwc0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 =
mtu 1500
>>>>     options=3D80008<VLAN_MTU,LINKSTATE>
>>>>     ether 62:73:64:5d:6a:ec
>>>>     media: Ethernet autoselect (none)
>>>>     status: no carrier
>>>>     nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
>>>> ELF ldconfig path: /lib /usr/lib /usr/lib/compat
>>>> Starting devd.
>>>> add net fe80::: gateway ::1
>>>> add net ff02::: gateway ::1
>>>> add net ::ffff:0.0.0.0: gateway ::1
>>>> add net ::0.0.0.0: gateway ::1
>>>> Generating host.conf.
>>>> Waiting 30s for the default route interface: .....(no carrier)
>>>> Creating and/or trimming log files.
>>>> Starting syslogd.
>>>> Clearing /tmp (X related).
>>>> Updating motd:.
>>>> Mounting late file systems:.
>>>> Configuring vt: blanktime.
>>>> Generating RSA host key.
>>>> 2048 SHA256:efid4fCpKZlmdi69b18qj+SNx2mSPQNr6ourB/w9tPw =
root@freebsd (RSA)
>>>> Generating ECDSA host key.
>>>> 256 SHA256:bpBVM0B9a3xDhmy3bvoC4OuELAJ4fvJd+p3tNwgia6k root@freebsd =
(ECDSA)
>>>> Generating ED25519 host key.
>>>> 256 SHA256:VHMKoDA1Zv50CmxiLJwTIvg58S2DuBg6zj2VFXDGq/M root@freebsd =
(ED25519)
>>>> Performing sanity check on sshd configuration.
>>>> Could not load host key: /etc/ssh/ssh_host_dsa_key
>>>> Starting sshd.
>>>> Could not load host key: /etc/ssh/ssh_host_dsa_key
>>>> Starting cron.
>>>> Starting background file system checks in 60 seconds.
>>>> lock order reversal:
>>>> 1st 0xc4499814 ufs (ufs) @ =
/usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
>>>> 2nd 0xd90169a0 bufwait (bufwait) @ =
/usr/home/emoe/Projects/ARM/src/sys/ufs/ffs/ffs_vnops.c:263
>>>> 3rd 0xc45c15d4 ufs (ufs) @ =
/usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
>>>> stack backtrace:
>>>> mount: /dev/mmcsd0s2: Device busy
>>>>=20
>>>> Thu Mar 31 10:49:29 UTC 2016
>>>>=20
>>>> FreeBSD/arm (freebsd) (ttyu0)
>>>>=20
>>>> login:
>>>>=20
>>>>> On Mar 30, 2016, at 7:47 PM, Erik Moe <e.moe@rcn.com> wrote:
>>>>>=20
>>>>> I was able to build a working odroid-c1 image not too long ago.  =
Let me pull the latest sources and see if something has changed.
>>>>>=20
>>>>> Erik=20
>>>>>=20
>>>>>> On Mar 30, 2016, at 2:24 AM, Daniel Braniss <danny@cs.huji.ac.il> =
wrote:
>>>>>>=20
>>>>>> Hi,
>>>>>> Managed to make a bootable SD, cross compile world/kernel,
>>>>>> but the kernel startup gets stuck, I can=E2=80=99t even get into =
the debugger.
>>>>>> any help/hints most welcome :-)
>>>>>> btw, I can also boot via the network, cutting down the debug =
cycle considerably.
>>>>>> thanks,
>>>>>> danny
>>>>>> PS: here is the console output
>>>>>> <s1>
>>>>>> _______________________________________________
>>>>>> freebsd-arm@freebsd.org mailing list
>>>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>>>>> To unsubscribe, send any mail to =
"freebsd-arm-unsubscribe@freebsd.org"
>>>>> _______________________________________________
>>>>> freebsd-arm@freebsd.org mailing list
>>>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>>>> To unsubscribe, send any mail to =
"freebsd-arm-unsubscribe@freebsd.org"
>>>>=20
>>>=20
>>> _______________________________________________
>>> freebsd-arm@freebsd.org mailing list
>>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>>> To unsubscribe, send any mail to =
"freebsd-arm-unsubscribe@freebsd.org"
>>=20
>=20




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?77D2CAED-B44A-4602-8C70-C3DD0A8D089C>