Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 17 May 2005 00:11:15 -0700
From:      Eugene Hercun <eugene.hercun@gmail.com>
To:        freebsd-questions@freebsd.org
Subject:   highpoint rocketraid 454 - RAID 1
Message-ID:  <c04ca341050517001132fd5c85@mail.gmail.com>

next in thread | raw e-mail | index | archive | help
OK, I'm seriously stuck. I have searched every resource exhaustively,
found bits and pieces, but not what I'm after. This is *honestly* my
last resort.
I have a HighPoint RocketRAID 454 with two Western Digital 200GB disks
(I was hoping to boot FBSD off of these). I've setup a RAID 1 array
under the bios utility program, and ran the FreeBSD 5.4 installer. I
remember seeing two different disks (ad4, ad6) when it came to
formatting/partitionning but I thought nothing of it. Until of course,
I wanted to see if there was a way, other than rebooting, to check the
RAID 1 status. I started reading through atacontrol(8) and found that
I could use 'atacontrol status ar0' which gave me:
atacontrol: ioctl(ATARAIDSTATUS): Device not configured

I do not see anything in my dmesg relating to ar0 being up and
running, and displaying the sub-disks which would explain why
atacontrol would be giving me that error message. However, I do see
that the RAID card, and the two disks, ad4, ad6, have been detected
properly.

I will attach my dmesg output below.
Thank you in advance.

Eugene




$ dmesg

Copyright (c) 1992-2005 The FreeBSD Project.

Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994

        The Regents of the University of California. All rights reserved.

FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005

    root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC

ACPI APIC Table: <ASUS   A7V8X-X >

Timecounter "i8254" frequency 1193182 Hz quality 0

CPU: AMD Athlon(TM) XP 2200+ (1791.22-MHz 686-class CPU)

  Origin =3D "AuthenticAMD"  Id =3D 0x681  Stepping =3D 1

  Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>

  AMD Features=3D0xc0400000<AMIE,DSP,3DNow!>

real memory  =3D 536854528 (511 MB)

avail memory =3D 515678208 (491 MB)

ioapic0: Changing APIC ID to 2

ioapic0 <Version 0.3> irqs 0-23 on motherboard

npx0: <math processor> on motherboard

npx0: INT 16 interface

acpi0: <ASUS A7V8X-X> on motherboard

acpi0: Power Button (fixed)

Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000

acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0

cpu0: <ACPI CPU> on acpi0

acpi_button0: <Power Button> on acpi0

pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0

pci0: <ACPI PCI bus> on pcib0

agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem
0xf8000000-0xfbffffff at device 0.0 on pci0

pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0

pci1: <ACPI PCI bus> on pcib1

pci1: <display, VGA> at device 0.0 (no driver attached)

pci1: <display> at device 0.1 (no driver attached)

atapci0: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port
0xa400-0xa4ff,0xa800-0xa803,0xb000-0xb007,0xb400-0xb403,0xb800-0xb807
irq 17 at device 14.0 on pci0

ata2: channel #0 on atapci0

ata3: channel #1 on atapci0

atapci1: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port
0x8800-0x88ff,0x9000-0x9003,0x9400-0x9407,0x9800-0x9803,0xa000-0xa007
irq 17 at device 14.1 on pci0

ata4: channel #0 on atapci1

ata5: channel #1 on atapci1

uhci0: <VIA 83C572 USB controller> port 0x8400-0x841f irq 21 at device
16.0 on pci0

usb0: <VIA 83C572 USB controller> on uhci0

usb0: USB revision 1.0

uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1

uhub0: 2 ports with 2 removable, self powered

uhci1: <VIA 83C572 USB controller> port 0x8000-0x801f irq 21 at device
16.1 on pci0

usb1: <VIA 83C572 USB controller> on uhci1

usb1: USB revision 1.0

uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1

uhub1: 2 ports with 2 removable, self powered

uhci2: <VIA 83C572 USB controller> port 0x7800-0x781f irq 21 at device
16.2 on pci0

usb2: <VIA 83C572 USB controller> on uhci2

usb2: USB revision 1.0

uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1

uhub2: 2 ports with 2 removable, self powered

pci0: <serial bus, USB> at device 16.3 (no driver attached)

isab0: <PCI-ISA bridge> at device 17.0 on pci0

isa0: <ISA bus> on isab0

atapci2: <VIA 8235 UDMA133 controller> port
0x7400-0x740f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 17.1 on
pci0

ata0: channel #0 on atapci2

ata1: channel #1 on atapci2

pci0: <multimedia, audio> at device 17.5 (no driver attached)

vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0x7000-0x70ff mem
0xdd800000-0xdd8000ff irq 23 at device 18.0 on pci0

miibus0: <MII bus> on vr0

rlphy0: <RTL8201L 10/100 media interface> on miibus0

rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

vr0: Ethernet address: 00:0c:6e:22:7b:e2

fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0

fd0: <1440-KB 3.5" drive> on fdc0 drive 0

ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7
drq 3 on acpi0

ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode

ppc0: FIFO with 16/16/16 bytes threshold

ppbus0: <Parallel port bus> on ppc0

plip0: <PLIP network interface> on ppbus0

lpt0: <Printer> on ppbus0

lpt0: Interrupt-driven port

ppi0: <Parallel I/O> on ppbus0

sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acp=
i0

sio0: type 16550A

atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0

atkbd0: <AT Keyboard> irq 1 on atkbdc0

kbd0 at atkbd0

orm0: <ISA Option ROMs> at iomem 0xd0000-0xd3fff,0xc0000-0xccfff on isa0

pmtimer0 on isa0

sc0: <System console> at flags 0x100 on isa0

sc0: VGA <16 virtual consoles, flags=3D0x300>

sio1: configured irq 3 not in bitmap of probed irqs 0

sio1: port may not be enabled

vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0

Timecounter "TSC" frequency 1791219738 Hz quality 800

Timecounters tick every 10.000 msec

acd0: CDROM <GCR-8523B/1.03> at ata1-slave PIO4

ad4: 190782MB <WDC WD2000JB-00GVA0/08.02D08> [387621/16/63] at
ata2-master UDMA100

ad6: 190782MB <WDC WD2000JB-00GVA0/08.02D08> [387621/16/63] at
ata3-master UDMA100

Mounting root from ufs:/dev/ad4s1a



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?c04ca341050517001132fd5c85>