Date: Fri, 21 Jul 2006 15:41:23 -0700 From: "Derrick Ryalls" <ryallsd@gmail.com> To: "Rich Demanowski" <richd@richdphoto.com> Cc: freeBSD <freebsd-questions@freebsd.org> Subject: Re: Enabling sound? Message-ID: <d5eb95fc0607211541m6f8beac4o96fb6fc593d305f0@mail.gmail.com> In-Reply-To: <44C156DA.5060701@RichDPhoto.com> References: <44C14EEB.5030901@RichDPhoto.com> <d5eb95fc0607211526h7ac4f642qce1903a616ab4527@mail.gmail.com> <44C156DA.5060701@RichDPhoto.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On 7/21/06, Rich Demanowski <richd@richdphoto.com> wrote: > Derrick Ryalls wrote: > > On 7/21/06, Rich Demanowski <richd@richdphoto.com> wrote: > >> I just dropped a SoundBlaster Live! card into my box, and have followed > >> the directions in the handbook and the man pages. > >> > >> The following lines are in the compiled kernel: > >> device sound > >> device snd_emu10k1 > >> > >> I don't get the pcm0 lines that section 7.2.2 in the manual talks > >> about. cat /dev/sndstat returns: > >> FreeBSD Audio Driver (newpcm) > >> Installed devices: > >> and nothing else. > >> > >> kldload snd_emu10k1 yields no output whatsoever. When followed by cat > >> /dev/sndstat it produces the same outputs as above. > >> > >> kld_load snd_driver yields: > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0x20 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> ppc0: parallel port not found. > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> > >> I recompiled with the sound and emu10k1 drivers commented out, and the > >> kldload and cat /dev/sndstat commands still yield the same. > >> > >> I need to get sound enabled on this box, so I can do some online > >> training provided through streaming video. Please, please, please tell > >> me I don't have to break down and install wankers on this thing ... > >> > > > > I would try this: > > > > kldload snd_driver > > > > then cat /dev/sndstat to see if perhaps a different driver is needed. > I tried that. That's what got me all the ppc0 and sio1 errors. > > Sorry, missed that. Record heat around here. My only other suggestion would involve a different sound card or possibly try a live O/S disk to see if the hardware is good.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?d5eb95fc0607211541m6f8beac4o96fb6fc593d305f0>