Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 8 Feb 2007 19:24:08 +0900
From:      KAWAGUTI Ginga <ginga-freebsd@ginganet.org>
To:        freebsd-stable@freebsd.org
Cc:        ginga-freebsd@ginganet.org
Subject:   panic: interrupt from missing bus(HP xw8400 WS)
Message-ID:  <20070208102408.GA58055%ginga@ginganet.org>

next in thread | raw e-mail | index | archive | help
Hi.

I'm using [6.2-STABLE of Tue Feb  6 16:17:03 JST 2007],
and HP xw8400 PC with 4GB memory, 2.0GHz Xeon x1.
Other configuration is SAS(on-board), SCSI(see below).


When FreeBSD-6-stable boots with this PC, it always panics at
very first stage of booting just after loader.

* Only way I can boot with this PC is to select 
  "safe-mode" at loader selection(no SMP, etc...).

* Disabling ACPI(as below), is not sufficient.

   loader> unset acpi_load
   loader> set hint.acpi.0.disabled=1

* GENERIC kernel also behaves the same.

* Same thing happens with 6.2-R or before.

-------------------------------------------------------
boot message going panic:
...
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:   0
 cpu1  (AP): APIC ID:  1
ioapic0: Assuming intbase of 0
ioapic1: Assuming intbase of 24
ioapic2: Assuming intbase of 48
panic: interrupt from missing bus
cpuid - 0
Uptime: 1s
Automatic reboot in 15 seconds ....


-------------------------------------------------------
full boot message(with SAFE-mode):

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-STABLE #2: Tue Feb  6 16:17:03 JST 2007
    ginga@somewhere.example.org:/usr/obj/usr/src/sys/SIMPLE
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU            5130  @ 2.00GHz (1995.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4e33d<SSE3,RSVD2,MON,DS_CPL,VMX,TM2,<b9>,CX16,<b14>,<b15>,<b18>>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 3757899776 (3583 MB)
avail memory = 3678396416 (3507 MB)
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 16 Entries> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 2.0 on pci0
pci16: <PCI bus> on pcib1
pcib2: <PCIBIOS PCI-PCI bridge> at device 0.0 on pci16
pci30: <PCI bus> on pcib2
pcib3: <PCIBIOS PCI-PCI bridge> at device 0.0 on pci30
pci32: <PCI bus> on pcib3
pcib4: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci30
pci31: <PCI bus> on pcib4
bge0: <Broadcom BCM5752 A1, ASIC rev. 0x6001> mem 0xfb600000-0xfb60ffff irq 5 at device 0.0 on pci31
bge0: firmware handshake timed out
miibus0: <MII bus> on bge0
brgphy0: <BCM5752 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:17:08:xx:xx:xx
pcib5: <PCIBIOS PCI-PCI bridge> at device 0.3 on pci16
pci17: <PCI bus> on pcib5
mpt0: <LSILogic SAS/SATA Adapter> port 0x1000-0x10ff mem 0xfd410000-0xfd413fff,0xfd400000-0xfd40ffff irq 10 at device 6.0 on pci17
mpt0: [GIANT-LOCKED]
mpt0: MPI Version=1.5.12.0
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x12
mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required).
mpt0: mpt_cam_event: 0x16
mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required).
pcib6: <PCIBIOS PCI-PCI bridge> at device 3.0 on pci0
pci96: <PCI bus> on pcib6
pcib7: <PCIBIOS PCI-PCI bridge> at device 4.0 on pci0
pci64: <PCI bus> on pcib7
pci64: <display, VGA> at device 0.0 (no driver attached)
pcib8: <PCI-PCI bridge> at device 5.0 on pci0
pci254: <PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 6.0 on pci0
pci253: <PCI bus> on pcib9
pcib10: <PCI-PCI bridge> at device 7.0 on pci0
pci252: <PCI bus> on pcib10
pci0: <multimedia> at device 27.0 (no driver attached)
pcib11: <PCI-PCI bridge> irq 3 at device 28.0 on pci0
pci8: <PCI bus> on pcib11
pcib12: <PCIBIOS PCI-PCI bridge> at device 0.0 on pci8
pci9: <PCI bus> on pcib12
mpt1: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem 0xf8400000-0xf841ffff,0xf8420000-0xf843ffff irq 3 at device 4.0 on pci9
mpt1: [GIANT-LOCKED]
mpt1: MPI Version=1.2.14.0
uhci0: <UHCI (generic) USB controller> port 0x3000-0x301f irq 3 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x3020-0x303f irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x3040-0x305f irq 10 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x3060-0x307f irq 5 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf8b04000-0xf8b043ff irq 3 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <EHCI (generic) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib13: <PCIBIOS PCI-PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib13
fwohci0: <Texas Instruments TSB43AB22/A> mem 0xf8a04000-0xf8a047ff,0xf8a00000-0xf8a03fff irq 11 at device 5.0 on pci1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:60:b0:00:00:1c:2a:a3
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:60:b0:1c:2a:a3
fwe0: Ethernet address: 02:60:b0:1c:2a:a3
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 63XXESB2 SATA300 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x30b0-0x30bf irq 11 at device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pnpbios: error 0/82 getting device count/size limit
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xccfff,0xcd000-0xce7ff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/13 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1995008280 Hz quality 800
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
acd0: DVDR <HL-DT-STDVD+-RW GSA-H21L/1.04> at ata1-slave PIO4
da0 at mpt0 bus 0 target 0 lun 0
da0: <HP DG072A8B54 HPD7> Fixed Direct Access SCSI-5 device 
da0: 300.000MB/s transfers, Tagged Queueing Enabled
da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C)
...



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20070208102408.GA58055%ginga>