Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 29 Mar 2005 07:53:07 +0800
From:      John Mok <jmok@attglobal.net>
To:        Julian Elischer <julian@elischer.org>
Cc:        freebsd-net@freebsd.org
Subject:   Re: HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i
Message-ID:  <424898E3.8080007@attglobal.net>
In-Reply-To: <42485836.6030203@elischer.org>
References:  <42344AF7.6070701@attglobal.net> <423C72A1.7060000@cronyx.ru> <4240497D.5030304@attglobal.net> <42404B15.5040605@elischer.org> <424835C0.9070603@attglobal.net> <42485836.6030203@elischer.org>

next in thread | previous in thread | raw e-mail | index | archive | help

The command "ngctl types" shows :-

There are 5 total types:
      Type name   Number of living nodes
      ---------   ----------------------
         socket       1
        rfc1490       0
            lmi       0
    frame_relay       0
        sync_ar       2

What other modules are needed? How to add them, whether load them 
dynamically or compiled into kernel?

Thanks a lot.

John Mok


Julian Elischer wrote:

> what does
> "ngctl types"
> say?
>
> looks like you don't have all the right modules loaded..
>
>
> John Mok wrote:
>
>>
>> After issuing the following commands :-
>>
>> #ngctl mkpeer sync_ar0: frame_relay rawdata downstream
>> #ngctl mkpeer sync_ar0:rawdata lmi dlci0 ansi
>> #ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490
>> #ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet
>> #ifconfig ng0 1.2.3.4 5.6.7.8
>> ifconfig: interface ng0 does not exist
>
>
>
>
> are you SURE none of these returned an error?
>
>>
>> The command ifconfig shows :-
>>
>> rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>    options=8<VLAN_MTU>
>>    inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1
>>    inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255
>>    ether 00:07:40:09:0f:09
>>    media: Ethernet autoselect (none)
>>    status: no carrier
>> xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>    options=9<RXCSUM,VLAN_MTU>
>>    inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2
>>    ether 00:01:03:c1:9c:58
>>    media: Ethernet autoselect (100baseTX <full-duplex>)
>>    status: active
>> xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>    options=9<RXCSUM,VLAN_MTU>
>>    inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3
>>    inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255
>>    ether 00:01:03:34:61:af
>>    media: Ethernet autoselect (100baseTX <full-duplex>)
>>    status: active
>> plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>>    inet6 ::1 prefixlen 128
>>    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
>>    inet 127.0.0.1 netmask 0xff000000
>>
>> and the command "ngctl list" shows :-
>>
>> There are 4 total nodes:
>>  Name: ngctl811        Type: socket          ID: 00000011   Num hooks: 0
>>  Name: <unnamed>       Type: frame_relay     ID: 00000004   Num hooks: 1
>>  Name: sync_ar1        Type: sync_ar         ID: 00000002   Num hooks: 0
>>  Name: sync_ar0        Type: sync_ar         ID: 00000001   Num hooks: 1
>>
>> Would it be the problem that I test it with cable disconnected from 
>> the modem (i.e.CSU/DSU)?
>>
>> Thanks a lot.
>>
>> John Mok
>>
>>
>> Julian Elischer wrote:
>>
>>> did the last command do anything?
>>>
>>> please show the output of:
>>> ifconfig
>>> ngctl list
>>>
>>>
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?424898E3.8080007>