Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 28 Mar 2005 16:47:55 -0800
From:      Julian Elischer <julian@elischer.org>
To:        John Mok <jmok@attglobal.net>
Cc:        freebsd-net@freebsd.org
Subject:   Re: HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i
Message-ID:  <4248A5BB.3040508@elischer.org>
In-Reply-To: <424898E3.8080007@attglobal.net>
References:  <42344AF7.6070701@attglobal.net> <423C72A1.7060000@cronyx.ru> <4240497D.5030304@attglobal.net> <42404B15.5040605@elischer.org> <424835C0.9070603@attglobal.net> <42485836.6030203@elischer.org> <424898E3.8080007@attglobal.net>

next in thread | previous in thread | raw e-mail | index | archive | help


John Mok wrote:

>
> The command "ngctl types" shows :-
>
> There are 5 total types:
>      Type name   Number of living nodes
>      ---------   ----------------------
>         socket       1
>        rfc1490       0
>            lmi       0
>    frame_relay       0
>        sync_ar       2
>
> What other modules are needed? How to add them, whether load them 
> dynamically or compiled into kernel?
>
> Thanks a lot.


kldload ng_iface at least

it should be loaded automatically if you add the line shown below..


>
> John Mok
>
>
> Julian Elischer wrote:
>
>> what does
>> "ngctl types"
>> say?
>>
>> looks like you don't have all the right modules loaded..
>>
>>
>> John Mok wrote:
>>
>>>
>>> After issuing the following commands :-
>>>
>>> #ngctl mkpeer sync_ar0: frame_relay rawdata downstream
>>

ngctl name  sync_ar0:rawdata fr-mux

replace the next line with..
#ngctl mkpeer fr-mux: lmi dlci0 ansi

and add:
ngctl name fr-mux:dlci0 lmi

>>> #ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490
>>
this could be replaved by:
ngctl mkpeer fr-mux: rfc1490 dlci16 downstream


>>> #ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet
>>
this line is totally confused..

should be:
ngctl name fr-mux:dlci16 protomux
ngctl mkpeer protomux: iface inet inet

now you can add the ip addresses..

sorry I didn't read it better several days ago..


>>>
>>> #ifconfig ng0 1.2.3.4 5.6.7.8
>>> ifconfig: interface ng0 does not exist
>>
>>
>>
>>
>>
>> are you SURE none of these returned an error?
>>
>>>
>>> The command ifconfig shows :-
>>>
>>> rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>>    options=8<VLAN_MTU>
>>>    inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1
>>>    inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255
>>>    ether 00:07:40:09:0f:09
>>>    media: Ethernet autoselect (none)
>>>    status: no carrier
>>> xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>>    options=9<RXCSUM,VLAN_MTU>
>>>    inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2
>>>    ether 00:01:03:c1:9c:58
>>>    media: Ethernet autoselect (100baseTX <full-duplex>)
>>>    status: active
>>> xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>>>    options=9<RXCSUM,VLAN_MTU>
>>>    inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3
>>>    inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255
>>>    ether 00:01:03:34:61:af
>>>    media: Ethernet autoselect (100baseTX <full-duplex>)
>>>    status: active
>>> plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
>>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
>>>    inet6 ::1 prefixlen 128
>>>    inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
>>>    inet 127.0.0.1 netmask 0xff000000
>>>
>>> and the command "ngctl list" shows :-
>>>
>>> There are 4 total nodes:
>>>  Name: ngctl811        Type: socket          ID: 00000011   Num 
>>> hooks: 0
>>>  Name: <unnamed>       Type: frame_relay     ID: 00000004   Num 
>>> hooks: 1
>>>  Name: sync_ar1        Type: sync_ar         ID: 00000002   Num 
>>> hooks: 0
>>>  Name: sync_ar0        Type: sync_ar         ID: 00000001   Num 
>>> hooks: 1
>>>
>>> Would it be the problem that I test it with cable disconnected from 
>>> the modem (i.e.CSU/DSU)?
>>>
>>> Thanks a lot.
>>>
>>> John Mok
>>>
>>>
>>> Julian Elischer wrote:
>>>
>>>> did the last command do anything?
>>>>
>>>> please show the output of:
>>>> ifconfig
>>>> ngctl list
>>>>
>>>>
>>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4248A5BB.3040508>