Date: Wed, 11 Oct 2000 23:52:48 +0400 (MSD) From: Igor Timkin <ivt@logger.gamma.ru> To: freebsd-stable@freebsd.org Subject: adaptec 39160 Message-ID: <200010111952.XAA22839@logger.gamma.ru>
next in thread | raw e-mail | index | archive | help
4.1.1-stable checked out today at 14.30 GMT:
FreeBSD news.gamma.ru 4.1.1-STABLE FreeBSD 4.1.1-STABLE #0: Wed Oct 11 18:56:19 MSD 2000 ivt@news.gamma.ru:/usr/src/sys/compile/NEWS i386
Adaptec 39160 rev.2.57.2, matherboard is ASUS P/I-P65UP5/C-P6ND, 2xPPro200.
During boot:
Waiting 2 seconds for SCSI devices to settle
(~30 sec pause)
Fatal trap 12: page fault while in kernel mode:
mp_lock = 01000002; cpuid = 1; lapic.id = 00000000
fault virtual address = 0x34
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc0134c7f
stack pointer = 0x10:0xff80df64
frame pointer = 0x10:0xff80df8c
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processer eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = cam <- SMP: XXX
trap number = 12
panic: page fault
mp_lock = 01000002; cpuid = 1; lapic.id = 00000000
boot() called on cpu#1
syncing disks...
done
Uptime: 1m2s
c0134a6c t ahc_set_recoveryscb
c0134aec T ahc_timeout
c013528c t ahc_abort_ccb
This kernel with 2940U2W (ahc1) work without problem:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1.1-STABLE #0: Wed Oct 11 18:56:19 MSD 2000
ivt@news.gamma.ru:/usr/src/sys/compile/NEWS
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (199.43-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 536870912 (524288K bytes)
avail memory = 519938048 (507752K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc02a1000.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> port 0xe800-0xe80f at device 1.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xe000-0xe0ff mem 0xfa000000-0xfa000fff irq 19 at device 9.0 on pci0
aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: <Adaptec 2940 Ultra2 SCSI adapter> port 0xd800-0xd8ff mem 0xf9800000-0xf9800fff irq 18 at device 10.0 on pci0
aic7890/91: Wide Channel A, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xd400-0xd41f mem 0xf9000000-0xf90fffff,0xfb000000-0xfb000fff irq 17 at device 11.0 on pci0
fxp0: Ethernet address 00:90:27:41:3d:89
ahc2: <Adaptec 2940 Ultra SCSI adapter> port 0xd000-0xd0ff mem 0xf8800000-0xf8800fff irq 16 at device 12.0 on pci0
aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ed0 at port 0x280-0x29f iomem 0xd8000-0xdbfff irq 5 on isa0
ed0: address 00:00:c0:a4:2e:61, type WD8013EPC (16 bit)
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
SMP: AP CPU #1 Launched!
ad0: 12416MB <QUANTUM FIREBALL CR13.0A> [25228/16/63] at ata0-master using WDMA2
Waiting 2 seconds for SCSI devices to settle
da4 at ahc1 bus 0 target 2 lun 0
da4: <IBM DDYS-T36950N S80D> Fixed Direct Access SCSI-3 device
da4: 80.000MB/s transfers (40.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da4: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da5 at ahc1 bus 0 target 3 lun 0
da5: <IBM DDYS-T36950N S80D> Fixed Direct Access SCSI-3 device
da5: 80.000MB/s transfers (40.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da5: 35003MB (71687340 512 byte sectors: 255H 63S/T 4462C)
da6 at ahc2 bus 0 target 11 lun 0
da6: <DEC RZ29B (C) DEC 0014> Fixed Direct Access SCSI-2 device
da6: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da6: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C)
da7 at ahc2 bus 0 target 15 lun 0
da7: <SEAGATE ST15150W 0023> Fixed Direct Access SCSI-2 device
da7: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da7: 4095MB (8388315 512 byte sectors: 255H 63S/T 522C)
da3 at ahc1 bus 0 target 0 lun 0
da3: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da3: 80.000MB/s transfers (40.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da3: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
Mounting root from ufs:/dev/da0a
da1 at ahc0 bus 0 target 1 lun 0
da1: <WDIGTL ENTERPRISE 1.80> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
da1: 2077MB (4254819 512 byte sectors: 255H 63S/T 264C)
da2 at ahc0 bus 0 target 2 lun 0
da2: <WDIGTL ENTERPRISE 1.91> Fixed Direct Access SCSI-2 device
da2: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
da2: 2077MB (4254819 512 byte sectors: 255H 63S/T 264C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <WDIGTL ENTERPRISE 1.80> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
da0: 4157MB (8515173 512 byte sectors: 255H 63S/T 530C)
vinum: loaded
vinum: reading configuration from /dev/da2d
vinum: updating configuration from /dev/da1d
vinum: updating configuration from /dev/da0s1d
current (2 Oct 2000) work without problem with 39160:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Mon Oct 2 21:56:00 MSD 2000
ivt@newsfeed.gamma.ru:/usr/obj/usr/src/sys/NEWSFEED
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 1073729536 (1048564K bytes)
avail memory = 1042632704 (1018196K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc029a000.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
pci0: <Intel PIIX4 ATA controller> at 4.1
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 4.2 irq 19
Timecounter "PIIX" frequency 3579545 Hz
pci0: <Intel 82371AB Power management controller> at 4.3
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xd000-0xd0ff mem 0xe2000000-0xe2000fff irq 19 at device 6.0 on pci0
aic7890/91: Wide Channel A, SCSI Id=7, 32/255 SCBs
ahc1: <Adaptec 3960D Ultra160 SCSI adapter> port 0xb800-0xb8ff mem 0xe1800000-0xe1800fff irq 18 at device 10.0 on pci0
aic7899: Wide Channel A, SCSI Id=7, 32/255 SCBs
ahc2: <Adaptec 3960D Ultra160 SCSI adapter> port 0xb400-0xb4ff mem 0xe1000000-0xe1000fff irq 19 at device 10.1 on pci0
aic7899: Wide Channel B, SCSI Id=7, 32/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xb000-0xb03f mem 0xe0000000-0xe00fffff,0xe0800000-0xe0800fff irq 17 at device 11.0 on pci0
fxp0: Ethernet address 00:d0:b7:5d:b4:a3
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xa800-0xa81f mem 0xdf800000-0xdf8fffff,0xe3000000-0xe3000fff irq 16 at device 12.0 on pci0
fxp1: Ethernet address 00:a0:c9:a3:5a:85
isa0: too many memory ranges
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
isa_dmainit(2, 1024) failed
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0303> can't assign resources
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled
Waiting 3 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0a
da6 at ahc2 bus 0 target 2 lun 0
da6: <IBM DPSS-318350N S80D> Fixed Direct Access SCSI-3 device
da6: 160.000MB/s transfers (80.000MHz, offset 63, 16bit)
da6: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C)
da4 at ahc1 bus 0 target 0 lun 0
da4: <SEAGATE ST118273LW 5766> Fixed Direct Access SCSI-2 device
da4: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da4: 17366MB (35566480 512 byte sectors: 255H 63S/T 2213C)
da5 at ahc1 bus 0 target 1 lun 0
da5: <SEAGATE ST118273LW 5766> Fixed Direct Access SCSI-2 device
da5: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da5: 17366MB (35566480 512 byte sectors: 255H 63S/T 2213C)
da2 at ahc0 bus 0 target 2 lun 0
da2: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da2: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da2: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da1: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da1: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
da3 at ahc0 bus 0 target 3 lun 0
da3: <IBM DDRS-34560D DC1B> Fixed Direct Access SCSI-2 device
da3: 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
da3: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
SMP: AP CPU #1 Launched!
vinum: loaded
vinum: reading configuration from /dev/da3d
vinum: updating configuration from /dev/da2d
vinum: updating configuration from /dev/da1d
vinum: updating configuration from /dev/da0d
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200010111952.XAA22839>